778623
63
Zoom out
Zoom in
Previous page
1/64
Next page
1 符号
一般性危险警告
请阅读使用说明书中的安全提示!
不得扔进生活垃圾。
断开电源线
建议、提示
操作指令
2 安全提示
警告! 请阅读所有安全提示和说明。如不
遵守安全提示和说明可能会导致触电、火
灾和/或重伤。
请保存好所有安全提示和说明,以备将来使用。
安全提示中使用的概念“电动工具”指使用电网电
力驱动的电动工具(带电源线)或使用电池驱动
的电动工具(无电源线)。
请注意电动工具的使用说明书。
3 按规定使用
AH-ES-ETS/ETSC 适用于与电动工具
ETS 125 REQ,ETSC 125 Li 搭配后用于打磨边
缘。
AH-ES-ETS/ETSC 不得与电动工具 ETS 125 EQ
或任何方形磨机鲁锹/三角磨机(DTS 400,
RTS 400,DTSC 400,RTSC 400)搭配使用。
请勿将 AH-ES-ETS/ETSC 与磨垫 ST-
STF 125/8-M4-J SW 搭配使用。该磨垫较
高的结构尺寸可能导致砂纸与滑动底座发生
碰撞。
4 设备元件
[1-1] 打磨模式设置
[1-2] 手柄
[1-3] 角度锁止装置的旋钮
[1-4] 角度指针
[1-5] 滑动底座按键
[1-6] 滑动底座
插图位于使用说明书的开始处。
5 组装
5.1 AH-ES-ETS/ETSC 安装在电动工具上[2]
将外壳 [2-2] 导入电动工具的保护装置凹槽
[2-3]
装入外壳零件 [2-1]
通过两个随附的螺栓和内六角扳手连接外
壳。
5.2 校准角度指针[3]
设备拥有可调节的角度指针。首次安装在电动工
具后必须在电动工具上校准角度指针。
将打磨模式调至“Hard”(见章节 6.1 )。
松开角度锁止装置的旋钮 [3-3]
通过测量工具将角度调至 90°。
拧紧角度锁止装置的旋钮。
松开角度校准装置的止动螺栓 [3-1]
移动角度指针 [3-2] ,直至指针指向 90° 标
记。
拧紧松开角度校准装置的止动螺栓。
6 设置
警告
伤害危险,电击
在设备上进行任何操作前,都应将电源插头
从插座上拔下!
6.1 打磨模式设置
Hard 模式[4a]
在 Hard 模式(预磨设置)下将根据设定的角度
打磨边缘。
Soft 模式[4b]
在 Soft 模式(中级研磨设置)下 AH-ES-ETS/
ETSC 会精准地根据已有表面进行调整,以防磨
穿油漆或填料。
6.2 设置打磨角度
见图 [5]
6.3 更换砂纸
见图 [6]
6.4 更换滑动底座
取下滑动底座 [7a]
装入滑动底座 [7b]
针对
粗糙表面请使用随附的滑动底座 LAS-H-
ES,
易损表面请使用带尼龙搭扣附着面和天
鹅绒滑条的滑动底座 LAS-W-ES。
6.5 更换滑条
见图 [8]
滑条 GB-LAS-STF-ES/5 可以作为耗材续购。
中文
63
63


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool ES-ETSC 125 - 2021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool ES-ETSC 125 - 2021 in the language / languages: All languages as an attachment in your email.

The manual is 2.35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info