Manual Festool DWC 18-4500 (page 17 of 99) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

574920

Zoom out

Zoom in

1/99

Removing the auto feed attachment

 Use power to carefully pull the attachment

from the gear box.

Setting the screw length

 Press button [9-1] to remove and insert the

depth stopper [9-2] and set the required screw

length.

Read the set screw length on the stopper sides

[9-3].

Inserting collated screw strips

 Pull the collated screws [10-3] through the

bottom guiding of the attachment, then push

the strip through the second guiding until it

engages in the working position.

 Pull the belt slightly to make sure that it is

safely ﬁ tted.

 Make sure that the ﬁ rst screw is in the screw-

ing axes – see ﬁ gure [10].

 Use the wheel [10-1] to set the required screw-

ing depth. Turn to the right for inserting the

screws deeper, and to the left to screw to lower

depth. The actual setting position is visible on

the presetting indicator [10-2].

Upon setting, set some screws for testing and use

the wheel [10-1] to adjust the depth, if required.

Each setting change complies with the stopper

shift o ± 0.1 mm.

 We recommend to screw in automatic mode –

see point 9.1 b).

Removing the collated screws

 Pull upwards to remove the belt (ﬁ gure [11]

) or press the transport lever and concurrently

pull the belt downwards (ﬁ gure [11] ).

10 Working instructions

- The auto feed attachment must not be held in

the depth stopper area as there are moving

parts!

- Each screw adjustment must be completed. In-

terrupted fastening or releasing of the pressure

during adjustment can result in unsatisfactory

machine function.

- The collated screws and the auto feed attach-

ment can only be replaced when the power tool

is turned off.

- Never use the auto feed attachment in any other

way than speciﬁ ed in this instruction manual.

- Use only original screwing bits.

- Use only original collated screws.

- Always store the collated screws in original

packaging.

- Always work in right angle against the attached

board.

Maintenance of the auto feed attachment

The attachment generally does not require any

maintenance. After long period use, we recom-

mend to clean with pressurized air.

The auto feed attachment may be lubricated in

the area of the carriage guide (see picture [12 b]).

Prior to cleaning, dismantle the attachment, as

speciﬁ ed above.

Prior to cleaning, remove the collated screws

from the attachment, as speciﬁ ed in the point

Removing the collated screws.

Pull the auto feed attachment from the drywall

screwdriver.

Disassembly of the slides

1. Push the depth stopper [9-2] into the housing

until the arresting button [12-1] is at the level

of the sign for dismantling the slides [12-2] –

see ﬁ gure [12 a].

2. Press the arresting button [12-1] and concur-

rently remove the slides from the holder – see

ﬁ gure [12 b].

3. Press the button [9-1] and concurrently re-

lease the depth stopper – see ﬁ gure [12 c].

Transport lever disassembly

1. Press the button [13-1] and concurrently pull

it out– see ﬁ gure [13 a].

2. Remove the released button [13-1] (figure

[13 b]) with the transport lever [13-2] and the

spring [13-3] from the slides (ﬁ gure [13 c]).

Clean individual parts, replace defective or worn

parts, and assemble in the opposite sequence.

CAUTION

During reassembly of the transport lever into

the slides, pay due care to correct ﬁ tting of the

spring [13-3] in the transport lever. Incorrect

assembly may result in dysfunction of the belt

transport.

Acoustic warning signal

Acoustic warning signals sound and the machine

switches off in the following operating states:

peep

- Battery ﬂ at or machine

overloaded

• Change the battery pack.

• Place the machine under

reduced stress.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool DWC 18-4500 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 11,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool DWC 18-4500 Manual

Product: