574907
15
Zoom out
Zoom in
Previous page
1/83
Next page
C 12 Li, C 15 Li
15
GB
7Settings
7.1 Changing direction of rotation
[1-8]
Switch to the left = clockwise rotation
Switch to the right = counterclockwise rotation
7.2 Changing gear
[1-4]
Gear switch forwards (digit 1 visible) = 1st gear
Gear switch to rear (digit 2 visible) = 2nd gear
7.3 Fastening
Adjust the switch so that its marking
[1-7]
faces the
screw symbol
[1-6]
.
Adjust the torque accordingly at the torque wheel
[1-
1]
.
Position 1 = low torque
Position 25 = high torque
An
acoustic signal
sounds when the preset torque is
reached and the machine then switches off. You must
release and press the ON/OFF switch
[1-9]
again to
start the machine.
7.4 Drilling
Adjust the switch so that its marking
[1-7]
faces the
drilling symbol
[1-5]
= maximum torque.
8 Tool holder, attachments
8.1 CENTROTEC tool chuck
[4]
Quick change of tools with CENTROTEC shaft
Only clamp CENTROTEC tools in CENTROTEC
tool chucks.
Wear gloves when replacing!
8.2 Chuck BF-FX
[5]
For clamping drill bits and bits with max. shaft diam-
eter of 13 mm.
Clamp tool centrally in the chuck.
8.3 Angle attachment DD-AS
[6]
Drilling and screwing at right angle to machine (part-
ly as an accessory).
8.4 Eccentric attachment DD-ES
[7]
Screwdriving near edges with bits according to ISO
1173 (partly as accessory).
8.5 Tool holder in the drill spindle
[8]
Bits can be inserted directly into the hexagon socket
holder of the drill spindle.
9 Working with the machine
9.1 On/Off switch
[1-9]
Press = ON, release = OFF
The speed of the machine depends on how far the
on/off switch is pressed in.
The LED bulb
[1-3]
lights up when the ON/OFF
switch is pressed
[1-9]
.
9.2 Bit depot
[1-2]
Magnetic, for storing bits and bit holders.
9.3 Acoustic warning signals
Acoustic warning signals sound and the machine
switches off in the following operating states:
LED green - flashes slowly
Battery pack is charged with
reduced current. Li-ion is
charged to 80 %.
LED green - lit continuously
Charging is complete or is not
restarted as current charge sta-
tus is greater than 80%.
LED red - flashes
General fault indication, e.g.
incomplete contact, short circuit,
defective battery pack, etc.
LED red - lit continuously
Battery temperature is outside
the permitted range.
WARNING
Risk of injury
Always switch off the machine before adjusting
settings!
WARNING
Risk of injury, electric shock
Always disconnect the battery pack before any
type of work on the machine!
Battery flat or machine overloaded.
Change the battery.
Place the machine under reduced
stress.
Machine is overheating.
You must allow the machine to
cool before using again.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool C15-15.6 V Li at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool C15-15.6 V Li in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 12,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info