634093

Ferm TSM1006 - FZT-250N Manual

3
Zoom out
Zoom in
Previous page
1/30
Next page
SPARE PARTS
REF.NR. DESCRIPTION FERM NR.
407820 POWER SWITCH 001
407821 GEAR 015
407402 LIFTINGWHEEL COMPLETE 016 T/M 019 + 023
407428 LOCK HANDLE 020
407405 RUTARY MARK 023
407822 MOTOR 024
407838 LIFT THREAD SPINDLE COMPLETE 025 T/M 028
407823 SPINDLE COMPLETE 032 T/M 040
407824 SPINDLE LOCK COMPLETE 040 T/M 045
407826 RIVING KNIFE SUPPORT 050
407827 FILLING PLATE 051
407828 LOCATION PIN 052
407408 FLANGE 057
407830 NUT M16 058
407411 ANGLE GAUGE COMPLETE 078 T/M 085
407831 LOCKING KNOB 085
407829 LOCKING KNOB 086
407825 CLAMPING LEVER 089
407832 SAWGUIDE COMPLETE 086 T/M 106
407833 TABLE INSERT 107 + 108
407414 RIVING KNIFE COMPLETE 109 T/M 113
407834 PROTECTION COVER SAW 114 T/M 119
407835 SET OF SCREWS FOR FLOORSTAND
407836 COVERS OF TABLE FEET
806202 BALL BEARING 6202 ZZ DRAW.2 REF.A
806204 BALL BEARING 6204 DRAW.2 REF.B
407837 MOTOR HOUSING (FRONT) DRAW.2 REF.D
58 Ferm
38 Use only saw blades recommended by the manufac-
turer. Do not use blades with a max. rated speed lower
than the rated speed of the machine. Only use saw
blades which comply with EN-847-1
39 Take care that the selection of the saw blade depends
on the material to be cut.
40 Connect circular saws to a dust-collecting device
when sawing.
41 Use and correct adjustment of the riving knife
42 Use and correct adjustment of the upper saw blade
quard.
43 Take care when slotting.
44 Do not use the machine for cutting fire wood.
SWITCH OFF THE MACHINE IMMEDIATELY WHEN
YOU DISCOVER:
1A defective mains plug or mains lead;
2A defective switch.
3 Overheating of the machine.
4 Smoke or odeur caused by scorched insulation.
TECHNICAL SPECIFICATIONS
Electrical safety
Always check that the power supply corre-
sponds to the voltage on the rating plate.
Replacing cables or plugs
Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert
the plug of a loose cable in the wall outlet.
Using extension cables
- As a supply for this machine always use an unloaded
line and/or an extension cable with conductors of at
least 1,5 mm
2
and protected with a 16 A fuse. Be sure
that this extension cable is not longer than 20 metres.
- Only connect your machine and/or extension cable to
an earthed electricity mains.
- This machine can be switched to the single-phase
network (230 V~/50 Hz). If you are in doubt about the
earth of the electricity provisions, consult an electri-
cian first.
Voltage | 230 V~
Frequency | 50 Hz
Power input | 1100 W
No load speed | 2950/min.
Saw blade dimensions | 250x30 mm
Number of teeths | Z30
Max. saw capacity 90º | 58 mm
Max. saw capacity 45º | 51 mm
Measurements of bench | 660x865 mm
(table including table extensions)
Suction mouth | 65 mm
Weight | 36 kg
L
pa
(sound pressure level) | 91.1 dB(A)
L
wa
(sound power level) | 101 dB(A)
Ferm 3
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm TSM1006 - FZT-250N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TSM1006 - FZT-250N in the language / languages: English, German, Dutch, Danish, French, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info