62 Ferm
BENCH PILLAR DRILL
THE NUMBERS IN THE FOLLOWING TEXT
CORRESPOND WITH THE PICTURES AT PAGE 2
Caution! For your own safety, carefully read these
instructions for use before using the machine.
CONTENTS:
1. Machine information
2. Safety instructions
3. Assembly
4. Operation, hints and tips
5. Maintenance
1. MACHINE INFORMATION
TECHNICAL SPECIFICATIONS
PRODUCT INFORMATION
Fig.A
1. On/off switch
2. Drill depth gauge
3. Protection guard
4. Motor
5. Drill depth lever
6. Table adjustment
Check first whether or not the delivery has been
damaged by transport and/or whether all the parts are
present.
2. SAFETY INSTRUCTIONS
The following pictograms are used in these instructions
for use:
CE Conforms to the applicable European safety
standards
Danger of bodily injury or material damage.
Indicates electrical shock hazard.
Read the instructions
Wear eye and ear protectors
Faulty and/or discarded electrical or electronic
apparatus have to be collected at the appropriate
recycling locations.
Carefully read this manual before using the machine.
Make sure that you know how the machine functions and
how to operate it. Maintain the machine in accordance
with the instructions to make sure it functions properly.
Keep this manual and the enclosed documentation with
the machine.
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions. Keep these
instructions in a safe place!
Before using the machine the guidelines must be taken
into consideration. Every mechanical or electrical
alteration to the machine which does not meet the
applicable guidelines carries a considerable accident risk.
DURING USE THE FOLLOWING POINTS
MUST BE CONSIDERED:
• Do not remove any mechanical or electrical
protective provisions.
• Check whether all the protective provisions are in
place and have been attached correctly.
• Wear safety goggles during drilling.
• If you have long hair, be sure to wear hair protection
(hair net or cap). Long hair can easily be caught in
moving parts.
• Wear fitted clothing; tie buttons on sleeves.
• Do not hold any workpieces in your hands when
drilling. Always use a machine clamp or another
clamping tool.
• Protect workpieces and clamping tools on the bench
to prevent them from getting caught. Fasten them
yourself with screws or clamp them to a machine
clamp fastened to the table.
• Check whether the drill holder is tightened properly.
• Check whether cable lead-throughs are okay.
• To remove drill chips only use hand brushes,
brushes, rubber wipers, chip hooks or similar aids.
• Do not carry out any cleaning or greasing work while
the machine is in operation.
• Always keep V-belts covered (so that your hands
cannot become caught).
• Only tighten the toothed ring drill holder by means
of the wrench.
• Never leave the wrench of the drill holder in the drill
holder! Before switching on the machine, check
whether the wrench really has been removed!
• Do not use any drills which are damaged on the shank.
• Drill is not suitable to use as press!
• If the mains cable is damaged, it may only be replaced
by a mains cable of the same type.
Voltage | 230 V
Frequency | 50 Hz
Power input | 450 W
No load speed | 220-2500/min
Number of speeds | 12 (R)
Chuck capacity/Morse Conical | 16 mm / MC-2
Weight | 60 kg
Lpa (sound pressure level) | 63.4 dB(A)
Lwa (sound power level) | 76.4 dB(A)
Vibration value | < 0,757 m/s
2
Ferm 3
SPARE PARTS LIST FPKB-16
FERM NR DESCRIPTION REF NR
301106 RACK 2
TDA1006 B-16/MC2 TAPER ARBOR FOR CHUCK 10
311111 CHUCK 16MM - B16 11
311106 SPRING 28
311107 CAP - SPRING 29
311103 MOTOR 38
311104 V-BELT 10 X 625 59
800156 V-BELT 10 X 560 59
311105 SWITCH 64
311109 KEY-DRIFT 79
