763638
3
Zoom out
Zoom in
Previous page
1/16
Next page
DRIFTSFEJL
Hvis slibemaskinen ikke funktionerer tilfredsstillende, gi-
ves nedenfor eventuelle årsager og afhjælpning.
1. Udsædvanlig mange gnister.
Dette tyder næsten altid på tilstedeværelse af smuds i
motoren eller på opslidte kulbørster.
-Få slibemaskinen kontrolleret hos Deres Ferm-
forhandler.
2. Slibemaskinen bliver for varm.
Slibemaskinen belastes for meget.
-Brug maskinen til det, den er beregnet til.
Motoren er defekt.
-Indlever slibemaskinen til reparation hos Deres
Ferm forhandler.
6. Støvet suges ikke op:
Dette kan eventuelt skyldes, at støvudsugningen er til-
stoppet.
-Rens åbningen til udsugning af støv.
Indlever slibemaskinen til reparation altid hos
Deres Ferm forhandler.
VEDLIGEHOLDELSE
Sørg for at maskinen ikke står under strøm, når
der udføres vedligeholdelsesarbejder på meka-
nikken.
Maskinerne fra Ferm er udviklet til at fungere lœnge uden
problemer med et minimum af vedligeholdelse. Ved at
rengøre maskinen regelmœssigt og behandle den kor-
rekt, bidrager De til en lœngere levetid for maskinen.
Rengøring
Rengør regelmœssigt maskinkappen med en blød klud,
helst efter hvert brug. Sørg for at ventilationshullerne er fri
for støv og snavs. Brug en blød klud, der er vœdet i sœbe-
vand til at fjerne hårdnakket snavs. Brug ingen opløs-
ningsmidler, så som benzin, alkohol, ammoniak, osv. Den
slags stoffer beskadiger kunststofdelene.
Smøring
Maskinen behøver ingen ekstra smøring.
Fejl
Kontakt Deres Ferm-forhandler, hvis der opstår fejl som
følge af slitage af en del.
Bagerst i denne brugsanvisning finder De en reservedel-
stegning med de reservedele, der kan bestilles.
MILJØ
For at undgå transportbeskadigelse leveres maskinen i
en solid emballage. Emballagen er så vidt muligt lavet af
genbrugsmateriale. Genbrug derfor emballagen.
Når de udskifter Deres maskinen bør De tage den gamle
maskine med til Deres lokale Ferm-forhandler. Der vil
maskinen blive bearbejdet på miljøvenlig vis.
GARANTI
Lœs det separat vedlagte garantikort for garantibetingel-
serne.
ClEl
KONFORMITETSERKLÆRING (DK)
Vi erklærer at under almindeligt ansvar, at dette
produkt er i overenstemmelse med følgende
normer eller normative dokumenter
EN50144-1, EN50144-2-4,
EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-3
i henhold til bestemmelserne i direktiverne:
98/37EEC,
73/23EEC,
89/336/EEC
01-07-2002
GENEMUIDEN NL
W. Kamphof
Quality department
30 Ferm
PRODUCT INFORMATION
Fig. A.
1. On/off switch
2. Adjusting wheel
3. Dust collection bag
4. Handle of paper clamp
5. Paper clamp
6. Sanding sole
7. Handle ( behind)
8. Blocking switchHandle ( front)
9. Handle ( front)
OPERATION
Choice of the sand-paper.
Coarse sand-paper (grain 50) removes in general the big-
ger part of the material and fine sand-paper is used for the
finishing. If the surface is not even, then start with rough
sand-paper. Further you use middlecoarse sand-paper
(grain 80) to remove the scratches left behind by the coar-
se sand-paper and finally you take fine sand-paper (grain
120) for the finishing.
Installing sand-paper.
The sanding machine is provided with a rectangle sand
sole. By tightening the sand-paper it does not wear out that
fast and so it will wear well longer.
Pull the mains plug out of the power-point;
•Open the back paper clamp by pulling the handle up.
Install the sand-paper under the clamp, see to the pa-
per being in the middle and look after the perforations
in the paper. They have to correspond with those on
the sand sole, so that the dust can be exhausted.
Push the handle back into its original position.
Repeat the operation to fix the sand-paper on the front
side.
Check all the time if the exhaust gaps are not stopped
up when you place the sand-paper, and check if the
perforations in the sand-paper correspond with the ex-
haust gaps.
Fix the sand-paper as tight as possible.
Before assembly sanding paper always remove
the plug from the mains.
1
3
5
6
2
7
8
4
5
Ferm 3
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm PSM1002 - FVM-250N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm PSM1002 - FVM-250N in the language / languages: English, German, Dutch, Danish, French, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info