763819

Ferm PRM4001 Manual

4
Zoom out
Zoom in
Previous page
1/6
Next page
Ferm 9
BEFORE USING THE ROUTER
Ensure the router switch is OFF and it is unplugged
from the mains before changing parts or acces-
sories, adjusting or inspecting this machine.
CHANGING/FITTING CUTTERS
-Make sure that the shank size of the cutter you are
using is the same size and compatible with the collet
in the machine.
-Make sure the cutter speed is the same or less than
that of the machine – see technical specifications.
-The cutter diameter must not exceed the maximum
diameter capacity of the machine- see technical spe-
cifications.
-Before replacing a cutter make sure the machine has
come to a complete stop and is switched off and
unplugged. Wait for the cutter to cool.
TO REPLACE A CUTTER
Refer to illustration below, press the spindle lock (7) and
turn the collet nut (6) until it engages the lock, keep the
spindle lock pressed.
-Loosen the collet nut using the spanner provided.
-Push the cutter into the collet making sure that the
shank is fully home.
-Tighten firmly with the spanner and release the
spindle lock
ASSEMBLING THE ACCESSORIES
Ensure the router is switched OFF and is unplugged
from the mains before changing parts or acces-
sories, adjusting or inspecting this machine.
MOUNTING THE PARALLEL GUIDE
Referring to the illustration below.
Attach the guide rods (18) to the guide (14) using the
bolts and spring washers provided.
Tighten securely with the 4mm Allen key provided.
Loosen thumbscrews (4) and slide the guide assembly
into the holes (5).
Adjust the guide to required distance.
Tighten thumbscrews.
ATTACHING THE GUIDE BUSH
The bush is used as a aid for cutting patterns. Ensure the
diameter of the cutter is suitable to use with the bush.
Referring to the illustration below, mount the bush on
the underside of the router base (3) with the flange facing
downwards.
Line up the holes in the bush with those on the base and
secure with the screws/bolts provided. Securely tighten
the screws/bolts.
4Ferm
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm PRM4001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm PRM4001 in the language / languages: English as an attachment in your email.

The manual is 0,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info