Manual Ferm PDM1001 - FPD-13-650 (page 3 of 14) (English, German, Dutch, Danish, French, Swedish, Spanish, Norwegian, Finnish)

763925

Zoom out

Zoom in

1/14

26 Ferm Ferm 3

grip.

•

Tighten the workpiece to a workbench by using a clamp.

•When all preparations are done the machine can be

connected to mains. First check if the switch is in the

‘OFF’-position and if the rotationswitch is in the

RIGHT-position.

3. OPERATION

1. THE ON/OFF SWITCH

Switch the machine on by pressing the triggerswitch (A).

When you release the triggerswitch (A) the machine will

turn off.

2. SWITCH-LOCK

You can lock the On/Off switch by pressing the triggers-

witch (A) and then pressing knob (B). Release the switch-

lock by pressing the triggerswitch (A) shortly.

3. SPEED-CONTROL

The rotation-speed can be

continuously adjusted be-

tween 0 and 2500 rota-

tions per minute, by pres-

sing the switch (A) deeper

or less deep.

4. ADJUSTING OF THE MAXIMUM ROTA-

TIONSPEED

Switch the machine on by pressing triggerswitch (A);

-Lock the triggerswitch (A) by pressing knob (B);

-Adjust the speed by turning the small wheel (C) to the

desired maximum rotation speed.

5. SWITCHING THE DIRECTION OF ROTA-

TION

-Direction of rotation counter-clockwise: shift switch

(D) to “L”;

-Direction of rotation clockwise: shift switch (D) to

“R”.

6. SWITCH FOR PERCUSSION DRILLING

With the switch on top

of the machine you can

select normal or percus-

sion drilling.

-Slide the switch to

the “Drill” symbol

for normal drilling;

-Slide the switch to the “Hammer” symbol for per-

cussion drilling.

4. MAINTENANCE

While maintaining and cleaning the machine

pull the plug from the mainssocket. Never use

water or other agressive liquids while cleaning

electrical parts of the lamp.

-Keep the mains cord of the machine clean, some fluids

contain solvents can dissolve plastic parts of the ma-

chine.

-Keep the ventilation slots of the machine clean to pre-

vent overheating of the motor.

5. MALFUNCTION

Below we have listed a number of possible causes and

corresponding solutions in case the machine does not

function as it should:

1. Excessive sparkling.

This usely indicates dirt in the motor or worndown

carbon brushes.

-Bring your percussion drill to your Ferm-dealer.

2. The percussion drill is overheating.

The ventilationslots are covered with dirt.

-Clean them with a dry cloth.

The percussion drill is overloaded.

-Use the machine for work for which it is ment to be.

-Replace the drill for a sharp one or sharpen the drill by

using a benchgrinder and a Twist drill grinding attach-

ment.

The motor is defect.

-Bring your percussion drill to your Ferm-dealer for re-

pairance.

ClEl

■

DECLARATION OF CONFORMITY (GB)

We declare under our sole responsability that this

product is in conformity with the following

standards or standardized documents

EN50144-2-1, EN50144-1

EN55014-1, EN61000-3-2, EN61000-3-3, EN55014-2

in accordance with the regulations:

98/37/EEC

73/23EEC

89/336/EEC

from 01-06-2000

GENEMUIDEN NL

G.M. Ensing

Quality department

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm PDM1001 - FPD-13-650 in the language / languages: English, German, Dutch, Danish, French, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm PDM1001 - FPD-13-650 Manual

Product: