Check for damaged parts
Do not use a tool with damaged parts, before further use a
damaged tool must be carefully checked by a qualified per-
son to determine that it will operate properly.
Check for alignment of moving parts, binding or breakage of
parts, mounting and other conditions that may affect its
operation.
A damaged part or guard should be properly repaired by an
authorised service centre, unless indicated otherwise in the
instruction manual. Have defective switches replaced by an
authorised service centre. Do not use a tool if the switch
does not turn on and off.
Have your tool repaired by an expert
This appliance is manufactured in accordance with rele-
vant safety standards. Only experts must carry out repai-
ring of electrical appliances, otherwise considerable dan-
ger for the user may result.
Storing tools
When not in use tools should be stored in the dry, out of
reach of children.
Lubrication
The machine requires a small amount of light oil on the
blade guide otherwise no other user lubrication
ENVIRONMENT
Recycle the packaging according to the identification
marks on it.
At the end of the product or its accessories life please
recycle where facilities exist - phone the Helpline for
current advice on recycling.
GUARANTEE
The guarantee conditions can be found on the separately
enclosed guarantee card.
We declare under our sole responsibility that this
product is in conformity with the following
standards or standardized documents
EN50144-2-10, EN50144-1
EN55014-1, EN55014-2, EN61000-3-2, EN61000-
3-3
in accordance with the regulations:
98/37/EEC
73/23/EEC
89/336/EEC
from 01-03-2000
GENEMUIDEN NL
W. Kamphof
Quality department
For any queries relating to operational or safety
matters contact:
Ferm Customer Helpline on: 0115 966 1199
Monday-Friday 8am – 6pm
Saturday 9am – 1 pm
CE
ı
DECLARATION OF CONFORMITY
(
UK
)
6 Ferm
PERSONAL SAFETY
Use Personal Protection Safety Equipment
Protect eyes with safety glasses or goggles note: the use
of safety protective eyewear without the CE mark can
lead to serious injury if the lens breaks. A suitable dust
mask should be worn if cutting, drilling or sanding is
dusty, in particular chipboard or MDF.
Approved safety footwear and headgear should worn as
appropriate, for example on building works or when
heavy weights are involved. Wear suitable gloves and
apron to protect against sparks/debris. Wear earplugs
or ear defenders.
Dress properly
Do not wear loose clothing or jewellery. It can get caught
in moving parts. Non-skid footwear is recommended
when working out doors. Wear protective hair covering
to contain long hair.
Stay alert
Watch what you are doing Use common sense. Do not
operate tools when tired or after taking alcohol or pre-
scription/ non-prescription drugs.
OPERATIONAL SAFETY
Warning!
This machine can produce fine dust, which is harm-
ful to your health – always wear a suitable dust mask and
other protection equipment as appropriate.
Concentrate
Routine and repetition can lead to mistakes. Remember
that a slight lack of concentration can result in serious
injuries in a split second.
Keep work area clean
Cluttered areas and benches invite injuries.
Consider the work environment
Do not expose power tools to rain or use them in damp
or wet locations. Keep work area well lit. Do not use
power tools in the presence of flammable liquids,
vapours or gases.
Guard against electric shock
This unit contains dangerous voltages. Use a RCD (resi-
dual current device) to provide protection against elec-
trical shock. Prevent body contact with grounded surfa-
ces (e.g. pipes, radiator, ranges or refrigerators).
Keep children and pets away
Do not let children or pets come into contact with the
tool, extension cable or work area.
Do not force the tool
It will work better and safer at the rate for which it was
intended.
Use the right tool
Do not force small tools or attachments to do the job of a
heavy-duty tool. Do not use tools for purposes for which
they were not intended; for example do not use a circular
saw for cutting trees or logs.
Do not abuse cable
Never carry the tool by the cable or pull it to disconnect
it from the power socket. Keep the cable away from heat,
oil and sharp edges. Do not touch the metal plug pins
when connecting or removing the plug.
Secure work
Use clamps or a vice to hold work. It is safer than using
your hand and it frees both hands to operate the tool.
Do not over-reach
Keep a proper footing and balance at all times.
Disconnect tools from power supply
When not in use, before servicing and when changing
accessories such as blades, bits and cutters. Always
switch off and unplug the saw from the power supply
before making adjustments or changing blades.
Remove adjusting keys and wrenches
Ensure that they are removed from the tool before swit-
ching on.
Avoid unintentional starting
Do not carry plugged in tools with your finger on the
switch. Check that the switch is off before plugging in to
socket.
Outdoor use extension cables
When the tool is used outdoors use only an extension
cable intended for outdoor use and marked accordingly.
Use a RCD (residual current device)
This provides protection against electrical shock. Do
not use in rain or damp conditions.
Connect a dust extraction device
Whenever there are facilities for fitting a dust of fume
extraction system, make sure it is connected and used.
Use recommended accessories
The use of any other accessory or attachment other than
recommended in the instructions or catalogue may pre-
sent a risk of personal injury. Use extension cables suita-
ble for the power input of the saw (minimum cable size
1.5mm2). When using a cable reel unwind the cable fully.
BEFORE USING THE SAW
Do not use this machine without the footplate
mounted. This saw is for hand held use only. Do not
fix to bench or clamp in vice. Make sure the saw is switched
OFF and unplugged from mains.
SELECTING SAW BLADES
Use universal fitting jigsaw blades suitable for Ferm jig-
saws.
In general fine tooth pitch gives a slower cleaner cut – as a
guide chose a pitch of 2.5 to 4.00mm for wood and 1.00
to 1.50mm for metal. Blade material, tooth profile and
hardness is important, for the best performance.
Choose blades manufactured for the material you are
using.
Ferm 3
