Manual Ferm HDM1023 (page 4 of 108) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

763888

Zoom out

Zoom in

1/108

with the mains power supply voltage?

• Are power cords, insulation and plug in

good order: sound, not loose or

damaged?

• Is there a good, firm connection at the

mains socket?

• Does the drill show any sign of abnormal

running, overheating or excessive

sparking?

• Whenever any of the problems mentioned

above appear, immediately cease using

the machine and have it repaired by an

expert.

• Wear ear protectors. Exposure to noise can

cause hearing loss.

• Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury.

Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord. Cutting accessory contacting a “live” wire

may make exposed metal parts of the power tool

“live” and give the operator an electric shock.



When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Always check that the mains voltage is

the same as on the type plate of the

machine.

Class II machine – Double insulation –

You don’t need any earthed plug.

Replacement of power cords or plugs

Immediately dispose of old cords and plugs once

they have been replaced. It is dangerous to plug a

loose power cord into a mains power socket.

Use of extension leads

Only ever use approved extension leads that are

suitable for the power rating of the machine. The

mini mum core thickness is 1.5 mm2. Whenever

using a reel extension lead, always fully unroll the

lead.

Immediately switch off the machine when:

• Excessive sparking of the carbon brushes and

verticiliosis in the collector.

• Interruption of the mains plug, mains lead or

mains lead damage.

• Defect switch

• Smoke or stench of scorched isolation



Hammer drills require very little operator

pressure. Excessive pressure on the tool

can lead to unnecessary overheating of

the motor, and burning of the driven tool.



The auxiliary handgrip can be rotated 360º around

the drill head, enabling safe and comfortable

operation, for both left and right-handed users:

• Loosen the handgrip by turning it

anticlockwise.

• Rotate the handgrip to the desire position.

• Retighten the handgrip in the new position.

Exchanging and removing drill bits

Fig. A+B

Before exchanging bits, first remove the

power plug from the wall socket.

Inspect bits regularly during use. Blunt

bits should be re-sharpened or replaced.

• Lightly oil the bit shaft before inserting it into

the chuck.

• Slide the locking sleeve (11) to the rear, and

insert the bit into the chuck opening. Ensure

that the keyway in the bit is seated properly in

the chuck, by carefully turning the bit until it

clicks into place. Release the locking sleeve.

• To remove the bit, slide and hold the locking

sleeve to the rear.



• Loosen the handgrip by turning it anticlockwise.

• Insert the depth gauge ruler through the hole

in the auxiliary handgrip.

• Slide the ruler to the desired depth.

• Retighten the screw firmly.



Fig. D

The correct position of the selection switch for

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm HDM1023 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 12,86 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm HDM1023 Manual

Product: