763623
3
Zoom out
Zoom in
Previous page
1/18
Next page
34 Ferm
surface without trails. Because of the circular move-
ment, how you hold and move the sanding machine is
of little importance. Additional pressure force on the
machine is rarely necessary. The sanding foot of the
sanding machine can be turned 360°. This makes it
easy to sand corners and the sandpaper wears evenly,
resulting in longer use of the sandpaper.
5. MAINTENANCE
While maintaining and cleaning the
machine pull the plug from the mainssoc-
ket. Never use water or other agressive
liquids to clean the machine. Clean the
machine by brushing it with a brush.
REGULAR MAINTENANCE OF YOUR SANDER
PREVENTS PROBLEMS.
1. Keep the ventilation slots of the machine clean to
prevent overheating of the engine.
2. Never use solvents for cleaning the plastic spare
parts. Liquids like brake fluid, benzine product with
petroleum, paint remover, etc. contain chemical mat-
ters which can damage, affect or destroy the plastic.
REPLACING THE SOLE
Before you are going to replace the sole
you have to disconnect the sander and you
have to pull the mains plug out of the
power source.
-The sole has to be replaced when the velcro has
been worn out.
-Remove the sandpaper of the sole.
-Remove the three screws which the sole is fixed to
the sander.
-Remove the sole.
-Install the new sole on thesander.
-Tighten the screws well.
6. TROUBLESHOOTING
In case the sanding machine does not work well, we
give you some possible causes and solutions.
1. The electromotor gets hot.
The air vents in the motor are filled up with dirt.
-Clean the cool ventilation slots.
The motor is defect.
-Have your sanding machine repaired or checked
by your local Ferm dealer.
2. The connected machine does not work.
Interruption in the mains connection.
-Check mains connection for fracture.
Defective mains switch
-Have your sanding machine repaired or checked by
your local Ferm dealer.
3. The dust is not extracted:
This can be caused by a full dust bag.
-Empty your dust bag.
This can be caused by a filled up dust extraction.
-Clean your dust collection opening.
Repairing of electric appliances may be carried
out only by experts.
ClEl
DECLARATION OF CONFORMITY (GB)
We declare under our sole responsibility that this
product is in conformity with the following
standards or standardized documents
EN50144-2-4, EN50144-1
EN55014-1, EN61000-3-2, EN61000-3-3, EN-55014-2
in accordance with the regulations:
89/392/EEC
73/23/EEC
89/336/EEC
from 01-06-2004
ZWOLLE NL
W. Kamphof
Quality department
Ferm 3
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm DSM1002 - FTS-260K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm DSM1002 - FTS-260K in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info