Ferm 69
have been replaced by new ones. It is dangerous to insert
the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the
power input of the machine. The minimum conductor
size is 1.5 mm
2
. When using a cable reel always unwind
the reel completely.
IMPORTANT SAFETY INSTRUCTIONS FOR
BATTERY AND BATTERY CHARGER
If you come into contact with acid from the battery,
immediately wash it off with water. If acid gets into
the eyes, rinse with plenty of water and consult a doctor!
1. Read and observe the operating instructions and
safety instructions for the battery and battery
charger before use!
2. Please note! Only use the battery and battery
charger delivered by the supplier to avoid the risk of
accidents.
3. Keep the battery, battery charger and the electrical
appliance away from damp, such as rain or snow.
4. Before using the battery charger, always check that
all the cables are correctly connected.
5. Do not use the battery charger if you see that its
cable is damaged. Have the damaged cable replaced
immediately.
6. If you are not using the battery charger, remove the
plug from the mains. Do not pull out the plug by the
cable.
7. If you drop the battery charger or it is interrupted by
another strong mechanical use, have it checked for
damage by a recognised professional workshop
before you use it again. Damaged parts must be
repaired.
8. Handle the battery with care. Do not drop it or
knock it.
9. Never try to repair the battery or battery charger
yourself. Repairs must always be carried out by a
recognised professional workshop to avoid the risk
of accidents.
10. Before cleaning or servicing the battery or battery
charger, always remove the charger's plug from the
mains.
11. Never charge the battery if the ambient temperature
is below 10° C or above 40° C.
12. The ventilation holes of the charger should always be
free.
13. The battery may not be short-circuited.
If short-circuiting occurs, power with a high
electrical current will flow. This can lead to the
battery overheating, catching fire or exploding, which can
result in damage to the battery or the user having an accident.
Therefore:
1. Do not connect cables to the poles of the battery.
2. Ensure that there are no metal objects (nails,
paperclips, coins, etc.) in the battery holder.
3. Do not leave the battery in water or rain.
4. Damaged battery chargers or batteries which can no
longer be charged should be disposed of as special waste.
Do not dispose of them together with domestic waste.
5. Never throw the battery into water or a fire, it may
explode.
3. OPERATIONS
TIGHTENING AND LOOSENING THE
BATTERY
Fig. B
Check that the outside of the battery or the machi-
ne is clean and dry before connecting the charger.
• Place the battery (5) in the foot of the machine as
indicated in the diagram. Press it into place until it
clicks into place.
• Press the locking buttons on both sides (10) before
loosening the battery and then pull the battery out of
the foot of the machine.
STARTING AND STOPPING
Fig. 1
The handle is designed with an unlock button to prevent
accidental starting.
• Press and hold the unlock button (3) located on
either side of the handle, then squeeze the main
switch (4)
• Release the main switch to stop the blades.
SELECT THE BLADE SUITABLE FOR YOUR
TASK
• The smaller shear blade is best for trimming grass
from around tree trunks and garden fixtures and for
shaping topiary.
• The larger hedge trimmer blade is best for larger
hedges and bushes.
THE CHANGE OF BLADE:
Fig. C
1. Fitted shear blade
2. Blade alignment with unit
3. Fitted hedge trimmer blade
4. Fixing screws
• Remove the battery pack, to prevent accidental
operation.
• Using the hex key provided, remove the 3 screws
fixing the blade to the tool.
• Take blade to be fitted and ensure that the raised cam
on the large drive gear aligns into the slot in the
moving section of the blade. (Fig. C). Place the blade
in position
• Re-fix the fixing screws.
• Attach battery and check operation of tool. If blade
does not operate correctly, stop immediately and
check mating of the blade slot to the gearbox cam.
Tip! If the appliance does not operate after replacing the
blade, please follow next instructions. This will often
solve the problem.
- Loosen the 3 screws several turns counterclockwise
- Push the start-button shortly; drive mechanism fits in
its place now
- Fasten the 3 screws again (turn clockwise)
4 Ferm
