510080

Ferm CDM1080 Manual

5
Zoom out
Zoom in
Previous page
1/96
Next page
5
EN
Product information
Fig. 1
1. Bit holder
2. On/Off-switch
3. Softgrip
4. LED (Red)
5. Charger connection
6. Extension piece
7. Bit
8. LED (White)
2. SAFETY INSTRUCTIONS
Explanation of the symbols
DESCRIPTION (FIG. A)
Denotes risk of personal injury, loss of
life or damage to the tool in case of
non-observance of the instructions in
this manual.
Indicates electrical shock hazard.
Indoor use only
In case of failure, the transformer is not
dangerous
Thermic protector
Do not dispose of in household waste.
Specific safety instructions
• Only use the accumulator block with the
battery charger provided – using other
chargers could be dangerous.
• Keep the accumulator block, tool and battery
charger away from damp and wet conditions.
• Before using the battery charger, check all
wires are properly connected.
• If any wires on the charger are damaged, do
not use it until these have been replaced.
• When the charger is not in use it should not be
plugged in.
When unplugging, do not pull the plug out by
the cable.
• If the charger breaks down or suffers from
other technical problems, take it to a
recognised dealership to be checked before
using it again. Any damaged parts must be
replaced.
• Take care when handling the accumulator
block, do not drop it or knock it against other
things.
• Never attempt to repair the battery charger or
accumulator block yourself; this can be
extremely dan gerous. Repairs should always
be carried out by a recognised dealership.
• Always unplug the charger before cleaning or
carrying out any other maintenance on it.
• Do not attempt to charge the accumulator
block in temperatures of below 5 degrees or
above 40 degrees centigrade.
• Never throw the accumulator block into water
or a re – it may explode.
• Turn the drill immediately off after the screw is
fasten ed. Overloading and damaging the
battery or motor can be prevented this way.
Use the torque to loosen the fastened screw
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of re, electric shock and personal
injury.
Read the following safety instructions and also
the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Class ll machine. Your machine is
double insulated; therefore no earthwire
is required.
Replacing cables or plugs
Immediately throw away old cables or plugs when
they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
3. ASSEMBLING INSTRUCTIONS
Inserting and removing bits
Fig. 1 + 7
The bits can easily be placed directly into the bit
holder or on the extension piece. The extension
piece can be used for screws that are difcult to
reach.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CDM1080 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM1080 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info