389294

Ferm cdm 1079 fpcd1800l Manual

5
Zoom out
Zoom in
Previous page
1/56
Next page
GB
5
Ferm
Loss of control can cause personal injury.
Use only impact drill bits and accessories that •
are designed for use with an impact drill when
using this machine in the impact drill mode.
Standard drill bits are NOT designed for use in
an impact drill and must NOT be used with an
impact drill. They may shatter and possibly
cause serious injury.
Do not drill material too small to be securely •
held.
Always keep hands out of the path of the drill •
bit. Avoid awkward hand positions where a
sudden slip could cause your hand to move
into the path of the drill bit.
Secure work piece. Use clamps or a vice to •
hold the work piece. It is safer than using your
hand and it frees both hands to operate the
tool.
Make sure there are no nails or foreign objects •
in the part of the work piece to be drilled.
To avoid injury from accidental starting, always •
remove the battery from the tool before
installing or removing a drill bit.
Do not install or use any drill bit that exceeds •
175 mm (7”) in lengths or extends more than
150 mm (6”) beyond the chuck jaws. They can
bend or break suddenly.
Before starting the operation, jog the switch •
shortly to make sure the drill bit does not
wobble or vibrate.
Do not use fly cutters or multiple-part hole •
cutters, as they can come apart or become
unbalanced during use.
Make sure the spindle has come to a complete •
stop before touching the chuck or attempting
to change the drill bit.
Always make sure the chuck is tight and the •
drill bit firmly tightened in the chuck before
starting the drill.
When drilling into smooth, hard surfaces such •
as metal, use a centre punch to mark the desi-
red hole location. This will prevent the drill bit
from slipping off centre as the hole is started.
Use a masonry bit with the drill in impact mode •
ONLY when drilling in concrete or masonry.
Always use carbide tipped masonry bits when •
drilling in concrete or masonry
This appliance is not intended for use by •
persons (including children) with reduced
sensory or mental capabilities, or lack of
experience and knowledge, unless they have
been given supervision or instructions
concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that •
they do not play with the appliance.
Follow all safety rules and warnings,
also those which are included with the
battery pack and charger used with this
tool. Failure to do so may result in
serious injury or damage to the charger
and the battery pack
3. MOUNTING ACCESSORIES
Prior to mounting an accessory always
remove the battery.
Installing the auxiliary handle
Fig. 1+2+3
Install the auxiliary handle for two handed
operation of the drill. This is particularly important
for impact drilling in concrete. The auxiliary handle
can be installed on either the left or right side of
the Impact drill.
Insert the threaded mounting screw through •
the depth stop rod clamp (14) and into the
threaded hole in the housing.
Turn the auxiliary handle (11) clockwise to •
tighten it into the housing.
Make sure the key on the depth stop
clamp is aligned with the notch in the
drill housing. This will prevent it from
unexpected turning and the auxiliary
handle from coming loose.
Screwdriver bits and drill bits can be stored in the
auxiliary handle.
To remove the end cap (15), pull it of the auxiliary
handle. To install, push it back on the auxiliary
handle.
Installing the depth stop rod
Fig. 1+2
The depth stop rod (7) is used as a gauge to
control the depth of the drilled hole. It can be used
with the Impact drill in either the normal drilling
mode or the impact drill mode.
Turn the auxiliary handle (11) counter •
clockwise about three turns to open the depth
stop rod mounting clamp (14).
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm cdm 1079 fpcd1800l at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm cdm 1079 fpcd1800l in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info