Manual Ferm BSM1020 (page 4 of 24) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

763826

Zoom out

Zoom in

1/24

Ferm 45

04 Ferm

Immediately switch off the machine when:

• Excessive sparking of the carbon brushes and

verticiliosis in the collector.

• Interruption of the mains plug, mains lead or

mains lead damage.

• Defect switch

• Smoke or stench of scorched isolation

Electrical safety

When using electric machines always observe

the safety regulations applicable in your country

to reduce the risk of fire, electric shock and

personal injury. Read the following safety

instructions and also the enclosed safety

instructions.

Always check that the power supply

corresponds to the voltage on the rating

plate.

Class ll machine. Your machine is

double insulated; therefore no earthwire

is required.

Replacing cables or plugs

Immediately throw away old cables or plugs

when they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in

the wall outlet.

Using extension cables

Only use an approved extension cable suitable

for the power input of the machine. The minimum

conductor size is 1.5 mm2. When using a cable

reel always unwind the reel completely.

3. OPERATION

Always observe the safety instructions

and applicable regulations.

Choice of the sand-paper

Coarse sand-paper (grain 50) removes in general

the bigger part of the material and fine sand-

paper is used for the finishing. If the surface is

not even, then start with rough sand-paper.

Further you use middle coarse sand-paper(grain

80) to remove the scratches left behind by the

coarse sand-paper and finally you take fine sand-

paper (grain 120) for the finishing.

Removing and Installing the sanding belt

Fig. C1 + C2

Before assembly the sanding belt

always remove the plug from the mains.

• Put the machine on its side, with the drive belt

cover down wards.

• Loosen the sanding belt fastener (4).

• Remove the sanding belt from the machine

• Put a new sanding belt on the machine, make

sure that the direction arrows on the sanding

belt are pointing in the same direction as the

direction indicator (5).

• Fasten the sanding belt fastener again (4).

Aligning the sanding belt

Fig. B

If the sanding belt doesn’t run parallel with the

outer edge of the housing, the sanding belt must

be aligned. Move the sanding belt in the correct

position with the adjusting knob (12). By turning

the adjusting knob clockwise the sanding belt will

move to the inside and by turning anti-clockwise

the sanding belt will move to the outside.

Switching on and off

Fig. B

• To switch the machine on press the on/off

switch (7).

• To switch the machine off release the on/off

switch.

If continuous operation is required the

blocking switch (8) must be used:

• Switch the machine on to press the on/off

switch.

• Press the blocking switch and release the

on/off switch.

• To switch the machine off press the on/off

switch again and release the on/off switch.

Mounting dustbag

Fig. B

A complete dust bag is enclosed. Put the wire-

bracket (inside the dust bag) into to the adapter

of the dust bag (when not mounted). The end of

the bracket has to point upwards. Use the dust

bag to collect dust which is released during

sanding.

• Put the dust bag on the dust collection

opening

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BSM1020 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,04 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm BSM1020 Manual

Product: