632795
4
Zoom out
Zoom in
Previous page
1/26
Next page
Ferm 49
hed power point installed in the nearness of the machine
and see that the lead can be guided to the contact without
cracks and pulls. If need be an earthed extension cable
can be used, but see that the cable is unrolled entirely and
that it is not in the way.
ELECTRICAL SAFETY
Always check that the power supply corresponds to the
voltage on the rating plate.
REPLACING CABLES OR PLUGS
Immediately throw away old cables or plugs when they ha-
ve been replaced by new ones. It is dangerous to insert the
plug of a loose cable in the wall outlet.
BEFORE OPERATION
For transport the machine has been greased with a layer
which prevents rust. This layer has no greasing function
and has to be removed with clothes. You can do this with a
solvant which is not aggressive, for example turpentine or
petroleum. When you are acquainted with metal-working
machines you can dismantle, control and oil several spare
parts with a light and universel machine-oil, for example
sewing-machine oil (sour free). Afterwards you finish the
complete maintenance table of chapter 14 ‘maintenance’.
ADJUSTMENT
The lathe has been adjusted to a minimum margin by the
factory. Because of transport some adjustments can be
changed. On the other hand the machine has been de-
signed in such a way that any appearing margin can be lif-
ted. This margin is also caused by wear end tear as a con-
sequence of an intensif use. If re-adjustment does not ha-
ve an effect anymore, the part is worned and has to be mo-
ved.
SPARE PART
Spindle tool slide
Tool slide
Spindle cross
slide
Cross slide
Transmission/
starting shaft
Tailstock
LIFTING A MARGIN
Loosen the front lock
nut, distort the back
lock nut clockwise,
until margin is mini-
mum, turn back a
fourth part and tighten
the front lock nut
Loosen the lock nuts,
tightening the
adjusting nuts
clockwise until margin
is minimum, tighten
lock nuts
Watch spindle tool
support
Watch tool slide idem
Loosen front lock nut
and tighten hindmost
lock nut until margin is
no longer noticeable,
turn back a quarter
part and tighten the
front lock nut
Loosen clamping nut,
unscrew both adjus-
ting nuts on both sides
a quarter part.
Move head with
adjusting screws until
the mark signs on the
right side of the head
correspond, tighten
the adjusting screws
again a bit without
moving the head, fix-
ing the clamping nut.
RECOURCES
2 hook
spanners
screw-driver,
open end
wrench
idem
idem
idem
screw-driver,
open end
wrench
4 Ferm
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm BLM1001 - MD350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BLM1001 - MD350 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info