Manual Ferm BGM1019 (page 5 of 44) (English, German, Dutch, French, Spanish)

632953

Zoom out

Zoom in

1/44

made of steel, it is advisable to use a wooden

block or plank between the grinder and the bench,

to insulate it and prevent vibration.

Assembly and adjustment of eye shield

bracket and eye shield

Fig. B

The eye shield bracket and eye shield

should only ever be assembled/adjusted

with the grinding wheel stationary, and

the machine disconnected from the

power supply.

• Fix the eye shield bracket (4) with attached

eye shield to the grinding wheel cover, using

the screw provided (A).

• Set the eye shield bracket at the correct height.

The clearance (B) between the wheel and the

eye shield bracket should be 1 to 1.5 mm.

• Next tighten the screw (A) firmly.

• Position the eye shield to give maximum

protection when working.

• Always wear safety glasses.

Fitting and adjusting tool rest

The tool rest should only be adjusted

when the grinding wheel is completely

stationary, and the machine is

disconnected from the power supply (the

wall socket).

• Fit the tool rest as shown in Fig. C.

• Fix it as tightly as possible in position, with a

maximum clearance (C) of 1 to 1.5 mm

between the tool rest and the grinding wheel.

Replacing the grinding wheel

Fig. C

Required tools:

• 19 mm spanner

• 8 mm spanner

• Screwdriver

Only ever replace the grinding wheel

when the motor is at a standstill and the

power is completely disconnected.

• Remove the grinding wheel guards using the

tools listed above. The spindle nut on the

right-hand side has a right-handed thread.

The spindle nut on the left-hand side has a

left-handed thread. Keep this in mind when

you are replacing the grinding wheels.

• Loosen the nut using the correct spanner.

Remove the old wheel from the spindle.

• Clean the flanges. Place one flange (A) back

on the spindle, with the hollow side facing the

grinding wheel. Slide the new wheel onto the

spindle. Place the second flange (A) on the

spindle, again with the hollow side facing the

grinding wheel. Now tighten the nut on the

spindle. Do not overtighten! Now refit the

grinding wheel cover, and again adjust the

tool rest correctly. Run the motor briefly,

without grinding.

4. Operation

Selecting the grinding wheel

Coarse grinding wheels will in general remove

the most material, and fine grinding wheels

are used for finishing. If the surface is uneven,

begin by using a coarse grinding wheel, and

grind the workpiece until it is smooth. Next use

a fine grinding wheel to remove the grooves and

scratching left by the coarse wheel, and finish off

the workpiece.

How to grind

To prevent the grinding surface from blocking

up, avoid holding wood, lead or any other soft

material or metal against the grinding wheel.

To avoid creating grooves, do not press the

workpiece too firmly on the grinding wheel. Use

water to regularly cool the workpiece being

ground. Wood chisels and the like should never

be sharpened ‘blue’.

Take care not to lose your grip on the object being

ground, as it may suddenly become jammed

between the tool rest and the grinding wheel. This

can cause the stone to shatter, the motor to seize,

or the workpiece to fly off, all of which can cause

injury and damage.

Whenever the machine has been in use for 30

minutes, it should be switched off. Allow the

machine to cool down to room temperature.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BGM1019 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 3,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm BGM1019 Manual

Product: