632850
2
Zoom out
Zoom in
Previous page
1/18
Next page
Ferm 35
AVAILABLE SPARE PARTS FOR BS-702
REF.NR. DESCRIPTION FERM NR.
4 BALL BEARING 6201 ZZ 806201
5 DRIVE ROLLER 402800
12 ADJUSTMENT BOLT 402801
14 IDLER ROLLER 402802
17 PLATE TABLE 402803
21 DRIVE PULLEY 402804
23 MOTOR 402805
27 BASE PLATE 402806
28 SWITCH 402807
30 BAR 402809
31 ADJUSTMENT BLOCK 402810
32 MOTOR PULLEY 402811
33 V-BELT M21 402812
36 ALUMINIUM DISC 402815
39 TABLE BRACKET 402816
40 TABLE TILT TRUNION 402817
41 MITRE BAR 402818
42 KNOB/BOLT FOR MITRE BAR 402819
46 TABLE 402820
47 MITRE GAUGE 402821
49 SHAFT FOR DRIVE ROLLER 402822
51 SHAFT FOR IDLER ROLLER 402823
52 BALL BEARING 6201 ZZ 806201
56 INDICATOR 402824
78 CAPACITOR (6 µF = 450 VAC) 402825
77 RUBBER FOOT 402826
2 Ferm
Product: Ferm Belt sander
Type BS-702, Article number 330702
Ferm, Genemuiden, The Netherlands
Sound pressure level L
pa
71 dB(A)
SERIAL NUMBER
The serial number on the machine consists of the fol-
lowing elements.
Serial nr.
READ THIS MANUAL CAREFULLY BEFORE USING
THE BELT SANDER!
1. SPECIFIC SAFETY RULES
BEFORE USING THE MACHINE:
1. The following points need to be checked:
- Do the connecting voltage of the machine corre-
spond with the mains voltage;
- Are the mains lead and the mains plug in a good
condition; strong, without ravels or damages.
2. For functional reasons the turning parts of this machi-
ne are not covered. Therefore it is of utmost impor-
tance to be careful. Hold the workpiece firmly, to
prevent it from slipping from your hands. Never
touch the sanding surfaces of a working machine with
your hands.
3. Avoid the use of long extension cables.
4. If necessary, secure the sanding machine with screws.
BEFORE YOU OPERATE THE MACHINE:
1. Always keep the mains cable away from moving parts
of the machine;
2. Use safety goggles;
3. Use a dust mask.
IMMEDIATELY SWITCH OF THE MACHINE
IN CASE OF:
1. defective mains plug, mains line or damage to the
mains line;
2. defective switch;
3. smoke or bad smell caused by scorched isulation.
2. INSTALLATION
Avoid the use of long extension cables. If necessary, secu-
re the sanding machine on a working bench with help of
screws through the holes in the feet of the machine fra-
me. Do not forget to leave enough space around the ma-
chine for the workpieces to be sanded.
3. DESCRIPTION
This machine combines all the advantages of a horizontal
and a vertical belt sander with those of a disc sander. Its
sturdy construction in cast iron and steel makes the ma-
chine suitable for every sanding job.
4. BEFORE PUTTING THE MACHINE
INTO OPERATION
OPERATION (SEE FIG. 1)
1. Machine frame;
2. Motor;
3. Roller stop and parallel stop;
4. Clamping handle;
5. Transport roller;
6. Sanding belt;
8. Fence;
9. Drive roller;
10. Aluminium disc;
11. Sanding disc;
12. Work plate;
13. Mitre scale;
14. Supporting arm.
ASSEMBLY
- Put the machine frame on its head and press the four
rubber stops into the foot of the frame.
- Machine frame, aluminium disc (10) and work plate
(12) are supplied in separate packaging.
- Push the aluminium disc on the shaft and fasten the
ORDER NUMBER/YEAR OF CONSTRUCTION
230 V~
50 Hz
375 W
1'
n
0
= 1450/min (disc)
V
0
= 275 m/min (belt)
1'
150 mm
915 x 100 mm
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm BGM1001 - BS702 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BGM1001 - BS702 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info