763617

Ferm AGM1027 - FDAG-750 Manual

5
Zoom out
Zoom in
Previous page
1/52
Next page
GB
5
Ferm
The speed of the machine must not exceed the
value on the grinding disc.
Make sure that the dimensions of the grinding •
disc correspond to the specifications of the
machine.
Make sure that the grinding disc has been •
mounted and fastened properly. Do not use
reducing rings or adapters to make the grinding
disc fit properly.
Treat and store grinding discs in conformance •
with the supplier’s instructions.
Do not use the machine for grinding •
workpieces with a maximum thickness
exceeding the maximum grinding depth of the
grinding disc.
Do not use grinding discs for deburring.•
When grinding discs have to be mounted on •
the thread of the spindle, make sure that the
spindle has sufficient thread. Make sure that
the spindle is sufficiently protected and does
not touch the grinding surface.
Before use, inspect the grinding disc for any •
damage. Do not use grinding discs which are
cracked, ripped or otherwise damaged.
Before use, let the machine run idle for 30 •
seconds. Immediately switch off the machine in
case of abnormal vibrations or occurrence of
another defect. Carefully inspect the machine
and grinding disc before switching the machine
on again.
Make sure that sparks do not put people into •
danger or that they contact highly flammable
substances.
Make sure that the workpiece is sufficiently •
supported or clamped. Keep your hands away
from the surface to be cut.
Always wear safety goggles and hearing •
protection. If desired or required also use
another kind of protection like for example an
apron or helmet.
Ensure that mounted wheels and points are •
fitted in accordance with the manufacturer’s
instructions.
Ensure that blotters are used when they are •
provided with the bonded abrasive product and
when they are required.
If a guard is supplied with the tool never use •
the tool without such a guard.
For tools intended to be fitted with threaded •
hole wheel, ensure that the thread in the wheel
is long enough to accept the spindle length.
Ensure that ventilation openings are kept clear •
when working in dusty conditions. If it should
become nessesary to clear dust, first
disconnect the tool from the mains supply (use
non metallic objects) and avoid damaging
internal parts.
Though poor conditions of the electrical mains, •
shortly voltage drops can appear when starting
the equipment. This can influence other
equipment (eq. blinking of a lamp). If the
mains-impedance Zmax <0.348 Ohm, such
disturbances are not expected. (In case of
need, you may contact your local supply
authority for further information.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Your machine is double insulated;
therefore no earthwire is required.
Replacing cables or plugs
Immediately throw away old cables or plugs when
they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in the
wall outlet.
Using extension cables
Only use an approved extension cable suitable for
the power input of the machine. The minimum
conductor size is 1,5 mm2. When using a cable
reel always unwind the reel completely.
3. ASSEMBLY
Prior to mounting an accessory always
unplug the tool.
Mounting the side-handle
Fig. 1
The side handle can be used for both left-hand
and right-hand control.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm AGM1027 - FDAG-750 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm AGM1027 - FDAG-750 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 11,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info