Ferm 13
4. Keep visitors away.
Visitors should be kept away from the work area at
all times. Do not let visitors handle the Electric
Rotary Hammer Drill at any time.
5. Store unused tools.
When not is use keep tools out of reach of children.
Store in a dry and secure location.
6. Do not force tool.
Do not apply undue pressure as this may affect
performance and may cause damage to the machine.
Forcing the job also increases the potential for
accidents.
7. Use right tool.
Do not force small tools or attachments to do the
job of heavy duty tool. Do not use a tool for purposes
not intended.
8. Dress properly.
Do not wear loose clothing or Jewellery. They can be
caught in moving parts. Rubber gloves and nonskid
footwear are recommended when working
outdoors. Wear protective hair covering to contain
long hair.
9. Use safety glasses.
Also use face or dust mask when operation is dusty.
10.Connect dust extraction equipment
If devices are provided for the connection of dust
extraction and collection facilities ensure these are
connected and properly used.
11.Do not abuse cord.
Never carry tool by cord or yank it to disconnect it
from electrical socket. Keep cord from heat, oil and
sharp edges.
12.Secure work.
Use clamps or a vice to hold work. It’s safer than
using your hand and it frees both hands to operate
tool.
13.Do not overreach.
Keep proper footing and balance at all times.
14.Maintain tools with care.
Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and
changing accessories. Inspect tool cords periodically
and, if damaged, have repaired by authorized service
facility. Inspect extension cords periodically and
replace if damaged. Keep handles dry, clean and free
from oil and grease.
15.Disconnect tools.
When not in use, before servicing and when changing
accessories such as blades, bits and cutters.
16.Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and
adjusting wrenches are removed from tool before
turning it on.
17.Avoid unintentional starting.
Do not carry plugged-in tools with finger on switch.
Be sure switch is off when plugging in.
18.Outdoor use extension cords.
When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
Always use tool in conjunction with a residual circuit
breaker device.
19.Stay alert.
Watch what you are doing. Use common sense. Do
not operate tool when you are tired.
20.Check damaged parts.
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to
determine that it will operate properly and perform
its intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect
its operation. A guard or other part that is damaged
should be properly repaired or replaced by an
authorized service centre unless otherwise
indicated elsewhere in this instructions manual.
Have defective switches replaced by an authorized
centre. Do not use tool if switch does not turn on
and off.
21.Warning.
The use of any other accessory or attachment other
than recommended in this operation instructions or
the catalogue may present a risk of personal injury.
22.Have your tool repaired by an expert.
This appliance is manufactured to very high
standards and meets relevant safety regulations.
Repairs should only be done by a suitable qualified
electrical engineer or otherwise.
23. Hearing protection should be worn.
Special safety instructions
•Check that the maximum speed indicated on the
grinding disc corresponds to the maximum speed of
the machine. The speed of the machine must not
exceed the value on the grinding disc.
•Make sure that the dimensions of the grinding disc
correspond to the specifications of the machine.
•Make sure that the grinding disc has been mounted
and fastened properly. Do not use reducing rings or
adapters to make the grinding disc fit properly.
•Treat and store grinding discs in conformance with
the supplier’s instructions.
•Do not use the machine for grinding workpieces with
a maximum thickness exceeding the maximum
grinding depth of the grinding disc.
•Do not use grinding discs for deburring.
•When grinding discs have to be mounted on the
thread of the spindle, make sure that the spindle has
sufficient thread. Make sure that the spindle is
sufficiently protected and does not touch the
grinding surface.
•Before use, inspect the grinding disc for any damage.
Do not use grinding discs which are crack-ed, ripped
or otherwise damaged.
•Before use, let the machine run idle for 30 seconds.
Immediately switch off the machine in case of
abnormal vibrations or occurrence of another
defect. Carefully inspect the machine and grinding
disc before switching the machine on again.
•Make sure that sparks do not put people into danger
or that they contact highly flammable substances.
•Make sure that the workpiece is sufficiently
supported or clamped. Keep your hands away from
the surface to be cut.
•Always wear safety goggles and hearing protection. If
desired or required also use another kind of
protection like for example an apron or helmet.
•Ensure that mounted wheels and points are fitted in
accordance with the manufacturer’s instructions.
4Ferm
