443064
5
Zoom out
Zoom in
Previous page
1/7
Next page
TONE MASTER REAR PANEL FUNCTIONS
A. FUSE - The fuse is in the AC supply of the amplifier and will help to protect the amplifier in the
event of an electrical fault or tube failure. If a fuse blows, it should only be replaced by one with
the same type and rating. NEVER use a fuse of higher current rating as this could damage the
equipment and present a serious safety hazard. If the amplifier repeatedly blows fuses, it should
be checked out by an authorized Fender service center.
B. POWER SWITCH - This switch turns the AC power on and off. When this switch is OFF the
amplifier is completely shut down.
C. STANDBY SWITCH - This turns the amplifier on and off. In the STANDBY position, the ampli-
fier is off, although power is applied to the tube filaments to keep them warmed up and ready to
play. A good rule of thumb is to turn the power switch on and wait at least 50 seconds before
turning on the standby switch. Using this switch during short breaks will increase tube life.
D. IMPEDANCE SWITCH - This is labeled LO, MED and HI. This switch serves two functions.
One, to set the output impedance of the amplifier to best match the speaker impedance for max-
imum power. Second, to enable the amplifier to better achieve the cranked-up sound at a lower
volume. On the B CHANNEL, with a single Tone-Master enclosure, this switch should be set
according to the setting of the B CHANNEL volume knob: For volume settings of 3.5 and lower,
LO would be the appropriate setting. For settings of 3.5 to 7, MED is best. For settings above 7,
HI will produce full power and tone. This switch will not damage tubes or reduce tube life at
these settings. What it does do is increase the gain in the LO and MED settings and thereby bet-
ter approximate the Full volume sound at a lower level than by adjusting the VOLUME alone.
With a single 16enclosure, LO will produce 30 watts, MED will Produce 60 watts, and HI will
produce a full 100 watts. With two 16enclosures, (an 8 load), LO will produce 60 watts, and
MED will Produce 100 watts. In the A CHANNEL, the switch has the same function, although
blues players may like running the switch on LO all the time to get that great crying tone.
Conversely, a player looking for a New Wave Strat
®
tone might like the sound of the A CHANNEL
on HI.
E. SPEAKER - Plug in connection for speakers. This jack must be used as the primary connection
for speakers.
IMPEDANCE
MED HILO
CAUTION:
RISK OF ELECTRIC SHOCK
DO NOT OPEN
360W
AVIS:
RISQUE DE CHOC
ELECTRIQUE NE PAS OUVRIR
ATTENTION:
UTILISER UN FUSIBLE DE
RECHANGE DE MEME
TYPE ET CALIBRE
CAUTION:
TO REDUCE THE RISK OF
FIRE, REPLACE FUSE WITH
SAME TYPE AND RATING
T4A
250V
FUSE
CAUTION: CHASSIS SURFACE HOT
WARNING: TO REDUCE THE RISK
OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE
ATTENTION:
SUPERFICIE DE CHASSIS
CHAUDE
PARALLEL
SPEAKER JACKS
100W
4 min. TOTAL
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fender Tone Master at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fender Tone Master in the language / languages: English as an attachment in your email.

The manual is 0,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info