616404
3
Zoom out
Zoom in
Previous page
1/44
Next page
3
ADVANCED PRODUCT FEATURES
SafeSense
®
Technology
Stops shredding immediately when
hands touch the paper opening.
SilentShred
Technology
Shreds without noisy disruptions
PAPER/CARD OR CD
BASIC SHREDDING OPERATION
Plug in and
turn ON (I)
Continuous operation:
6QUPNJOVUFTNBYJNVN
NOTE: Shredder runs briefly after
each pass to clear entry. Continuous
operation beyond 8-minutes will
trigger 15-minute cool down period.
SafeSense
®
is active and
working properly
Touch test area and
look for the SafeSense
®
indicator to illuminate
SAFESENSE
®
TECHNOLOGY
SET-UP AND TESTING
Stops shredding immediately when hands touch the paper opening.
For more information about all of Fellowes Advanced Product Features go to www.fellowes.com
PRODUCT MAINTENANCE
TROUBLESHOOTING
TO CLEAN THE SENSORS
CLEANING AUTO-START INFRARED SENSORS
Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors
may become blocked by paper dust causing the motor to run even if there is no paper present.
(Note: two paper detection sensors are located in the center of the paper entry.)
"MMNJDSPDVUTISFEEFSTSFRVJSFPJMGPSQFBLQFSGPSNBODF*GOPUPJMFEB
machine may experience diminished sheet capacity, intrusive noise when
shredding, and could ultimately stop running. To avoid these problems, we
recommend you oil your shredder each time you empty your waste bin.
OILING SHREDDER
* Only use a non-aerosol vegetable oil in long
nozzle container such as Fellowes 35250
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
Locate Auto-start
infrared sensor
6TJOHDPUUPOTXBCXJQF
away any contamination
from the paper sensors
Dip cotton swab in
rubbing alcohol
Press and hold forward
(
) 2-3 seconds
*Apply oil across entry
3
4
1 2
Go to Support Section at www.fellowes.com or see back page of manual for useful telephone numbers.
Feed paper/card
straight into paper
entry and release
or
Hold CD at edge, feed
into center of entry
and release
When finished
shredding set to
OFF (O)
1
1
Turn the shredder ON
(I) to activate SafeSense
®
Turn OFF (O) and
unplug shredder
Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum operating temperature and needs to cool down. This
indicator will remain illuminated and the shredder will not operate for the duration of the recovery time. See Basic Shredding Operation for more information about
the continuous operation and recovery time for this shredder.
SafeSense
®
Indicator: If hands are too close to the paper entry, the SafeSense
®
indicator will illuminate and the shredder will stop shredding.
2 3
2
1 2 3
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fellowes Powershred 450Ms at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fellowes Powershred 450Ms in the language / languages: All languages as an attachment in your email.

The manual is 3,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info