616388
3
Zoom out
Zoom in
Previous page
1/44
Next page
3
BASIC SHREDDING OPERATION
ADVANCED PRODUCT FEATURES
SAFESENSE
®
TECHNOLOGY OPERATION
Stops shredding immediately when hands touch the paper opening.
SET-UP AND TESTING
Turn the shredder
ON (
)to activate
SafeSense
®
Touch test area and
look for the SafeSense
®
indicator to illuminate
SafeSense
®
is active
and working properly
3
10
HD-10c
s
2
Continuous operation:
6QUP
5-minute maximum
NOTE: Shredder runs briefly after each pass
to clear entry. Continuous operation beyond
5-minutes will trigger 20-minute cool
down period.
1
PAPER/CARD
Plug in and put disconnect
power switch in ON (I) position
Feed paper/card
straight into paper
entry and release
When finished shredding,
set to Off
2
4
Press Auto-On ( )
For more information about all of Fellowes Advanced Product Features go to www.fellowes.com
PRODUCT MAINTENANCE
HD-10
"MMDSPTTDVUTISFEEFSTSFRVJSFPJMGPSQFBLQFSGPSNBODF*GOPUPJMFEB
machine may experience diminished sheet capacity, intrusive noise when
shredding and could ultimately stop running. To avoid these problems, we
recommend you oil your shredder each time you empty your waste bin.
OILING SHREDDER
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
*Apply oil across entrySet to Off (O)
Press and hold Reverse
(R) 2-3 seconds
CLEANING AUTO-START INFRARED SENSORS
Paper detection sensors are designed for maintenance free operation. However, on rare occasions, the
sensors may become blocked by paper dust causing the motor to run even if there is no paper present.
(Note: two paper detection sensors are located in the center of the paper entry).
* Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250
TO CLEAN THE SENSORS
Locate Auto-start
infrared sensor
6TJOHDPUUPOTXBCXJQF
away any contamination
from the paper sensors
Dip cotton swab in
rubbing alcohol
Set to Off (O)
and unplug
3
1
1 2 3
HD-10C
s
4
TROUBLESHOOTING
Alternate slowly back and forthPress and hold
Reverse (R)
2-3 seconds
Set to Off
and unplug
Gently pull uncut
paper from paper
entry. Plug in
Shredder doesn’t start:
Yellow - SafeSense
®
active
Yellow flashing - SafeSense
®
not active
Wait 20 minutes for motor to cool down
Make sure head is on basket correctly
Remove and empty basket
PAPER JAM
Set to Auto-On ( )
and resume shredding
1
4
3
2
6
HD-10C
s
5
HD-10C
s
2
HD-10C
s
3
1
ATTENTION: If the SafeSense
®
light remains on, you must engage the
Override Switch in order to perform steps above.
Once the jam is cleared, reset the SafeSense
®
feature. (See SafeSense
®
instructions below.)
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fellowes POWERSHRED HD-10Cs at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fellowes POWERSHRED HD-10Cs in the language / languages: All languages as an attachment in your email.

The manual is 3,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info