Check there is enough clear space (min 50cm) behind the machine to allow
items to pass through freely.
Plug the machine into an easily accessible mains socket.
Neptune 2 - Fit the Exit Tray to the rear of the machine. The tray will hang
onto the machine in line with the exit aperture.
5
Let our experts help you with a solution.
Customer Service...
www.fellowes.com
Always call Fellowes before contacting your place of purchase, see the rear cover for contact details.
NEED HELP?
Switch the power on (located in the carry handle to the right side of the
machine).
Switch the ‘Standby’ button on at the control panel. Check the red power LED
is on. The machine will automatically warm-up to the 80 micron setting.
Select ‘Temp’ button to scroll through other pouch thickness settings as
required. The pouch setting will light yellow.
When the selected temperature is set, the green ready LED will flash and a
beep signal will sound.
Place the pouch, sealed edge first, into the pouch / document entry. Keep the
pouch straight and central within the document entry, not on an angle. Use
the entry markings as a guide.
Upon exit, the laminated pouch may be hot and soft. To prevent jamming
remove the pouch immediately. Place pouch on to a flat surface to cool. Take
care when handling a hot pouch.
4.
5.
6.
7.
8.
9.
10.
1.
2.
3.
SETTING UP THE LAMINATOR
HOW TO LAMINATE
Switch off the machine at the wall. Allow the machine to cool. The outside of the machine can be cleaned with a damp cloth. Do not use solvents or flammable materials to
polish the machine. Cleaning sheets can be used with the machine. When the machine is warm – run the sheets through the machine to clean any residue off the rollers. For
optimum performance, it is recommended that cleaning sheets are used with the machine regularly. (Cleaning sheet order codes #5320601)
ProblemPossible causeSolution
Anti-jam mechanism activates
(20 second auto-reverse)
The machine has detected debris pre-
venting the pouch proceeding correctly
Operate the machine with cleaning sheet to remove any debris on rollers.
Check pouch is correctly prepared with no folded corners.
Anti-jam mechanism activates
(5 seconds auto-reverse)
The machine has detected a curled corner
on the pouch
No ‘red’ Power on LEDMachine not switched onSwitch on machine at right side and at the wall socket
Ready light does not come on after a long
period
Machine is in a hot or humid areaMove the machne to a cooler and dry area
Pouch does not completely seal the item
Item may be too thick to laminateCheck pass through thickness is correctly selected and pass through again
Temperature setting may be incorrectCheck pouch thickness is correctly selected and pass through again
Pouch has waves or bubblesTemperature setting may be incorrectCheck pouch thickness is correctly selected and pass through again
Pouch is lost in the machinePouch is jammed
Select reverse button and pull out the item by hand
Jamming
Pouch was used ‘open end’ first
Pouch was not centred on entry
Pouch was not straight upon entry
Empty pouch was used
Pouch is damaged after laminationDamaged rollers or adhesive on rollersPass cleaning sheets through the machine to test and clean rollers
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Fellowes Neptune 2 laminator at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Fellowes Neptune 2 laminator in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.
The manual is 1,58 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
