Manual Felisatti JSF120 (page 5 of 40) (English, German, French, Italian, Portuguese, Spanish)

502491

Zoom out

Zoom in

1/40

intended for. This container should be kept as it will prove

useful for your work.

INSTALLATION

The environmental conditions, temperature, humidity, lighting,

the correct dislocation of your tool and the cleanliness of the

place of work are important conditions for personal safety

and tool performance. These factors should always be kept

under control in order to improve working conditions and

ensure safety.

ELECTRICAL CONNECTION

Before connecting the tool to themains make sure thatit

complies with the standard regulations of the country in

question, and that the voltage and frequency correspond to

the details on the data plate.When using extension leads,

make sure that cable cross-section conforms to the length of

the lead. When using a wind-up extension make sure that is

completely unwound so as to avoid overheating.

ATTENTION!-Theswitchonthistoolisttedwithalocking

device, allowing the tool to be operated for long periods of

timewithoutinterruptions.Beforeinsertingtheplugintothe

socket, check that the switch is in the unlocked position.

When the tool is not to be used for long periods remember to

leave the switch device in the unlocked position.

PLACE OF WORK

The tool that you have purchased is a portable electric power

tool. Only one user should operate this tool, given its shape,

weight and maneuverability. Normal use requires that both

oftheoperator’shandsarermlykeptonthemachineand,

under all circumstances, away from the applied tool.5The tool

is already regulated according to standard parameters by the

constructor when supplied. If necessary oscillation and speed

adjustments can be carried out on the “/E” model.

OSCILLATION REGULATION (g.1-2)

With this movement, during the working stroke, the blade

is pressed against work piece, during the return stroke the

blade is detached from the material in order to facilitate the

discharging of chips and reduce overheating. The regulation

of oscillatory movements can be carried out whilst the

machine is running: Switching from position “0” to position

“III” is by means of the lever N. In order to obtain maximum

working speed and the best results on any type of material,

the appropriate oscillation should be applied.- For wood and

soft synthetic material, maximum oscillation is required,

therefore the regulator should be set at position “III”.- For steel

and hard materials, the blade should not be forced against

the material, therefore the oscillation should be at minimum,

with the regulator be set at position “0”. - For materials with

intermediate hardness, such as aluminium or hard wood,

positions “I” or “II” should be used, after the appropriate tests

have been carried out. The values supplied are approximate

and can vary according to the thickness, hardness and the

berdirectionofthematerialandbladecondition.

SPEED REGULATION

In order to improve the machine performance, and provide

maximumworkingefciencyonalltypesofmaterial,usethe

saw model with electronic speed control.

TheorangeknurledknobH(Fig.1)ismountedonthebodyof

the machine and is marked with numbers from 1 to 6.Minimum

speed is at position 1 and the speed progressively increases

to max. speed at position 6. The following speeds are advised:

Low speed for cutting glass, ceramics, metal. Average speed

for cutting plastic, pressed or compensated materials. High

speed for cutting hard wood, soft wood and masonite panels.

Carefully choose the ideal speed for the work that has to be

performed by carrying out preliminary tests.

REGULATION OF SUPPORT BASE (g.3)

Angled cuts of up to 45° can be performed. In order to carry

out this operation proceed as follows:

- Overturn the machine

-Using anAllenwrench, loosen the athead screw which

holds the base onto the head of the machine.

- Adjust to the desired angle, with the aid of the graduated

scale.

-Re-tightentheatheadscrew.

OPERATION AND USE

Felisatti jig saws are particularly sturdy and resistant

machines; extremely versatile and maneuverable, ideal for

all continuous cutting work with wood, aluminum, plastic,

steel, etc.

1. STARTING

JSF120/750E

Pushthekeyforwardsuntilitlocksintoposition(directionI),

in this position the switch is locked in “ON”.

Attention: to unlock the switch, press the orange key towards

the position “0”.

JSF65/550E, JSF85/600E, JSF100/700E

Press the switch key, to lock it in ON, activate the lock push

button located next to the switch.

Attention

In order to unlock the switch, fully press the switch

key - in this manner the lock push button will trip

automatically.

2. HANDGRIP

JSF120/750E

The grip-shaped machine body allows the tool to be perfectly

guided, the knob handgrip, located on the head, completes

the tool governability.

Attention

During working operations both hands must be kept

rmly on the machine.

JSF65/550E, JSF85/600E, JSF100/700E

These machines are tted with “atiron” shaped bodies,

providing perfect grip and excellent balance under all working

conditions, resulting in incomparable maneuverability.

Attention

Given the special shape of the body, these machines can

be operated with only one hand, but for reasons of safety

it is strongly advised to keep both hands on the machine

during use.

HOLLOW WORK PIECES

A hole must be drilled in the material, in order to provide a

starting point for the saw.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti JSF120 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Felisatti JSF120 Manual

Product: