500406

Felisatti DCF10 Manual

5
Zoom out
Zoom in
Previous page
1/32
Next page
5
See general warranty conditions printed in separate.and drilling ceramics and for starting to drill brick without a
piercer.
• High speed (2) (lever forwards) (DCF10/10.8R) for
drilling brick, for drilling wood and derivatives, plastics and
metals.
The speed can be adjusted while the machine is run-ning.
However, this should not be done at full load. If, when the
machine is stopped, the selector C cannot be set in its nal
position, push the on/off E switch briey.
4. Attachment of bits in the keyless drill chuck
1. Open the drill chuck A and insert the drill bit or screwdriver
bit (in clamp H).
2. To block the bit or screwdriver tip, turn the drill chuck in
a clockwise direction, looking at the ma-chine from the front.
5. Torque adjustment
• For use as a screwdriver, the drill-screwdriver is equipped
with an adjustable clutch, operated by the torque adjustment
control B which has 15 settings. Once it has been correctly
adjusted, the friction clutch is released when the pre-selected
torque setting is reached, to avoid the screw penetrating too
far or damage to the machine. Adjustment depends on the
type and size of the screw used. It is advisable to always
begin in the lowest setting (1) and increase gradually until the
desired result is obtained.
• For use as a drill, set the torque adjustment control B to
the drill setting. The clutch is designed not to work in the drill
mode.
CHARGING THE BATTERY
To remove the battery F from the machine, press both side
buttons, G, situated on the handle, at the same time.
To charge the battery with a quick 45 minute charger, proceed
as follows:
1. Place the battery charger I on a at surface and plug the
charger into the mains.
2. Plug in the charger. the green light on
3. Put the battery in charger. If battery is in good condition,
the red light will be on. If the battery is in poor condition,the
red light will not be on. Please replace the battery.
4. The red light off when the battery is fully charged, ready
for use.
ACCESSORIES
Accessories and their corresponding order number can be
found in our catalogues.
MAINTENANCE AND CARE
Remove the battery before carrying out any opera-tion on
the machine.
- Clean the machine very carefully after each use. The air
vents should always be kept clear.
- Store in a dry place, away from cold .
- Use only Felisatti accessories and spares. These should
be tted in a Felisatti technical service centre (See Warranty/
Technical Service Centre address leaet).
- Brush replacement: The brushes disconnect auto-
matically and should be replaced after 80 - 100 hours use
or when they are less than 3 mm long. Have them replaced
by an Ofcial Service Centre. We re-commend that at every
second change of brushes, you take the machine to one of
our Ofcial Service Centres for general cleaning and oiling.
WARRANTY
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Felisatti DCF10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti DCF10 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info