502504

Felisatti BSF76 Manual

5
Zoom out
Zoom in
Previous page
1/29
Next page
5
CAUTION: The speed control I may be turned only between
numbers 1 and 6. Do not force the control beyond these
positions, otherwise it may break and fail to work.
STARTING THE TOOL
WARNING! The tool should not be in contact with the
surface of the part to be worked on when you start or stop it
- otherwise this could cause defective sanding or damage the
belt. To switch on the tool, pull the trigger switch H. Release
it to turn the tool off. and press the blocking button G. To stop
the tool when blocked, pull the trigger H again and release
it.
WORKING INSTRUCTIONS
To begin sanding, rst hold the tool rmly in both hands.
Switch on the tool and wait until it reaches the required
speed. Then carefully place the tool on the surface of the part
to be sanded. Keep the belt against the work constantly and
move the machine backwards and for-wards without pressing
too hard. Never force the tool.
The weight of the tool is sufcient to give adequate
performance and pressure. Excessive pressure may cause
jamming, overheating of the motor, burning of the part being
sanded and recoil.
Use the right type of belt for the surface being sanded and
the desired results.
CAUTION: Whilst sanding, always keep the lead to the back
of the machine to avoid it getting caught.
ACCESSORIES
Accessories and their corresponding order number can be
found in our catalogues.
MAINTENANCE AND CARE
WARNING! Always unplug the machine before carrying out
work on it.
- Inspect the mounting screws: Regularly inspect all the
mounting screws and ensure they are rmly tightened.
Should any screw be loose, tighten it immediately.
Failure to do so could put you at serious risk.
- Motor maintenance: Never press too hard when using the
sander. Excessive pressure may produce an over-load and
damage the motor or the part being sanded.
- Brush replacement: The brushes disconnect automati-cally
and should be replaced after 150-200 hours’ use or when
they are less than 10 mm long. Have them replaced by an
Ofcial Service Centre.
- To clean the sander thoroughly after use, unplug it from the
mains and use a dry brush to clean all orices.
- The vents of the machine should be kept clear at all times.
Use a clean damp cloth to clean the protective covers (do not
use solvents, petrol or turpentine).
- Check that the mains lead is in good condition. If it is not,
take it to an Ofcial Service Centre to have it replaced.
- Use only FELESATTI accessories and spares. The parts the
changing of which is not covered in this instruction manual,
should be replaced in a FELESATTI Ofcial Service Centre
(See Warranty/Ofcial Service Centre address leaet).
WARRANTY
See general warranty conditions printed on the attached
sheet.
Do not dispose of electric tools
in the household waste!
In accordance with European Directive 2002/96/EC
relating to old electrical and electronic appliances
and its translation into national law, used electric
tools must be collected separately and recycled in
an ecologically desirable way.
DECLARATION OF
CONFORMITY
We hereby declare, under our sole
responsibility, that the FELISATTI
brand products described in this
manual comply with the following
standards or standard documents:
EN60745-1:2009, EN60745-2-
4:2009, EN55014-2:1997+A1+A2,
E N 6 1 0 0 0 - 3 - 2 : 2 0 0 6 + A 1 + A 2 ,
EN61000-3-3:2008 in accordance
with EU Directives 2006/42/EC,
2006/95/EC, 2004/108/EC, 2002/96/
EC
Francisco Ruis
Technical director
We reserve the right to make technical changes 06/2011
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Felisatti BSF76 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti BSF76 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info