502505

Felisatti BSF100 Manual

4
Zoom out
Zoom in
Previous page
1/29
Next page
4
Follow very carefully the instructions in this manual, save it
and keep it close at hand, ready to carry out any inspection
of parts that may be necessary.
If the machine is used carefully and normal maintenance is
carried out, it will work well for a long time.
The functions and use of the tool you have bought shall be
only those described in this manual. Any other use of the tool
is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See gures)
A Lever (Fig.1 & 3)
B Steel plate (Fig.2)
C Adjustment screw (Fig.2)
D Sawdust extraction tube (Fig.2)
E Dust bag (Fig.3)
F Zip fastener (Fig.3)
G Blocking button (Fig.2)
H Trigger switch (Fig.1 & 2)
I Speed control (electronic model only) (Fig.2)
J Brush holder cover (Fig.3)
K Belt direction indicator arrow (Fig.2)
EQUIPMENT
- 1 sawdust and shaving collector bag
- 1 sanding belt (610x100) 80 grit
- Operating instructions
- Safety instructions
- Warranty
BRIEF DESCRIPTION
Any use differing from the above is strictly forbidden. Belt
sanders are devices equipped with powerful motors and an
“endless” abrasive belt, which rotates at great speed over two
rollers. These tools are perfectly adapted for grinding large
amounts of material in a short time: for instance, they are
ideal for rough-grinding wood, for rough sanding, for stripping
painted wood... However, they are not at all suitable for
achieving a ne nish.
BEFORE USING THIS TOOL
Before using the tool, make sure the mains voltage is correct:
it must be the same as that on the specication label.
Machines with 230V can also be connected to a 220-V mains
TECHNICAL DATA
supply.
Before plugging in the tool, always make sure that the trigger
switch works properly and returns to the “OFF” position when
released.
FITTING AND REMOVAL OF THE ABRASIVE BELT
WARNING! Always make sure that the tool is switched off
and unplugged before tting or removing the belt.
Follow the steps below:
1. Pull out lever A completely and t the belt over the rollers.
2. Make sure that the arrow on the back of the belt points in
the same direction as indicator arrow K on the tool.
3. Once the belt is tted over the rollers, push lever A back to
its original position.
4. Adjust the belt tracking: switch on the tool and make sure
the belt is properly aligned.
5. If the edge of the belt sticks out beyond the edge of the
steel plate B or is more than 6 mm from its inside edge, adjust
the belt tracking with the adjuster screw C.
DUST EXTRACTION
WARNING! Always make sure that the tool is switched off
and unplugged before tting or removing the dust bag.
The dust (sawdust) produced while sanding is extracted
into a sawdust collector bag. To t the bag, follow the steps
below:
1. Fit the collector bag (dust bag) E on the sawdust extraction
tube D.
2. Push it rmly onto the sawdust extraction tube D has far
as it will go to avoid the bag E coming off during operation. If
the machine does not extract all the dust, this is probably due
to the quality or moist charac-ter of the material. Blow off the
moist dust particles.
TIP: For best results we recommend emptying the bag E
when approximately half full and shaking it slightly to remove
as much sawdust as possible.
ELECTRONIC SPEED CONTROL
(only mod. FBS100CE)
The electronic speed control I enables the speed of the
sanding belt to be adjusted in different positions num-bered
from 1 al 6. To increase the speed, turn the control I towards
number 6, to decrease the speed, turn towards number 1.
Select the appropriate speed for the nish required and the
part you wish to sand.
Belt sander BSF76/900 BSF100/1200E
Rated power W 900 1200
Sanding belt speed m/min 250 200-400
Sanding belt measurements Mm 76 x 533 100 x 610
Acoustic pressure dB(A) 91,0 96,7
Sound-power level dB(A) 102,0 106,7
Vibration acceleration m/s² 3,7 5,5
Approximate weight (without accessories) according
EPTAProcedure 01/2003
Kg. 3,3 5,3
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Felisatti BSF100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti BSF100 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info