444922

Fe Powertools L Manual

2
Zoom out
Zoom in
Previous page
1/6
Next page
3 Manual magnetic drilling machines
1. Safety procedures
When using magnetic drilling machines please follow the general safety instructions for electric
power tools.
Please read the manual Use eye protection use ear protection
use safety helmet use safety gloves wear appropriate clothing
disconnect before opening use safety chain Warning for electrical shock
dangerous environment don’t use in wet places pacemaker warning
TIP: Do not use your magnetic drill on the same structure when ARC welding is in progress. D.C.
current will earth back through the magnet and cause irreparable damage.
WARNING: This appliance must be earthed.
1. Always secure the machine with the supplied safety chain before starting to operate, this to protect the user in case of power
failure or breaking loose of the magnet whilst in use.
2. Always wear safety goggles, gloves and ear plugs.
3. Disconnect from the power source when changing cutters or working on the machine.
4. Always ensure cutter retaining screws are secure – they sometimes vibrate loose in use.
5. Regularly clean the work area and machine., remove swarf and dirt, paying particular attention to the underside of the magnet.
6. With a gloved hand, after switching off the power, remove any swarf which might have gathered around the cutter and arbor
before proceeding to the next hole.
7. Remove tie, rings, watches and any loose adornments which might entangle with the rotating parts of the machine.
8. Should the cutter get stuck in the workpiece, stop the motor immediately to prevent personal injury. Disconnect from the
power source and push and pull the arbor by hand. DO NOT ATTEMPT TO FREE THE CUTTER BY SWITCHING THE MOTOR ON
AND OFF.
9. If the machine is accidentally dropped, always thoroughly examine the machine for signs of damage and check that it functions
correctly before trying to drill a hole.
10. Regularly inspect the machine and check the nuts and screws are tight.
11. Always ensure when using the machine in an inverted position that only the minimum amount of coolant is used and that care
is taken to ensure the coolant does not drip in the motor unit. We advise you to use special cutting paste which is specially
designed for inverted position drilling.
12. ONLY use spare parts advised by your dealer for magnetic drilling machines.
13. Use the magnetic drilling unit on a clean and flat surface only, to prevent the machine breaking out because of poor clamping
force.
14. If you discover any irregularity on machine cables immediately bring the machine to a recognized dealer for a repair or
maintenance service.
4 Manual magnetic drilling machines
2. Technical overview
FE 30 FE 32 FE 32 R/L FE 36 S FE 50 FE 50 R/L FE 100 R/L
Motor
800 W 900 W 1050 W 1080 W 1150 W 1150 W 1800 W
Spindle Direct – 19
mm Weldon
½”x20 NF
– 19 mm
Weldon
½”x20 NF –
19 mm
Weldon
Direct – 19
mm Weldon
MT 2 – 19
mm Weldon
MT 2 – 19 mm
Weldon
MT 3 – 19 mm
Weldon
Hole cutter
30 mm
30 mm 32 mm 32 mm 36 mm 50 mm 50 mm 100 mm
Hole cutter
55 mm
30 mm 32 mm 32 mm N/A 50 mm 50 mm 100 mm
Hole cutter
110 mm
N/A N/A N/A N/A 50 mm 50 mm 100 mm
Countersink
N/A N/A 30 mm N/A N/A 40 mm 55 mm
Reaming
N/A N/A N/A N/A N/A 23 mm 31.75 mm
Twist drills
N/A 13 mm 13 mm N/A 23 mm 23 mm 31.75 mm
Tap
N/A N/A M 16 N/A N/A M 20 M 30
RPM
450 min
‐1
450 min
‐1
0‐350 min
‐1
400 min
‐1
I 250 min
‐1
II 450 min
‐1
I 50‐250 min
‐1
II 100‐450 min
‐1
I 40‐140 min
‐1
II 120‐480 min
‐1
Stroke
80 mm 150 mm 150 mm 39 mm 150 mm 150 mm 250 mm
Weight
9.9 kg 12 kg 12 kg 11 kg 13 kg 13 kg 27 kg
Magnet
1500 kg 1500 kg 1500 kg 1200 kg 1700 kg 1700 kg 3500 kg
Check power supply
Make sure the used current corresponds with the machine specifications. When using a cable
extension make sure it can do the job.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fe Powertools L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fe Powertools L in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info