566107

Fakir BOSS Manual

10
Zoom out
Zoom in
Previous page
1/12
Next page
10
Before using the hair clipper:
The hair to be cut should be clean and dry or
damp. Carefully comb the hair to remove any
knots. Place a towel around the neck to prevent
any trimmed hair failing down inside the collar.
To prevent the electric shock, never use the
appliance near water/liquids when it is connected
to the mains supply.
Adjusting the cutting comb length:
You could cut your hair in 14 different lengths
with adjustable cutting combs. Please place the
adjustable cutting comb to the appliance. With
small cutting comb you could cut your hair
between 2mm-20mm and with large cutting comb
you could cut your hair between 22mm-40mm.
You could easily adjust the cutting comb length
with rotate switch on your appliance. By pulling
the rotate switch to upwards will rise the cutting
comb. There is an indicator left side of the
appliance that shows the cutting comb length.
You could find a table as below that shows hair
lengths equal to the cutting comb position.
NOTE: Hair thinner mechanism defines hair
style without changing the length of adjustable
cutting comb. By sliding the blade length control
switch, Titanium blades will rise. Rising Titanium
blades will provide hair to be cut easily and
provide best cutting performance of your
appliance.
Instructions for Hair Cutting:
NOTE:
If you are cutting for the first time, start
with the maxi-mum comb length (40mm).
Nape of the neck (Diagram A): Set the comb
position between 3mm and 6mm.Hold the clipper
with the blade teeth pointing upwards. Begin
starting at the centre of the head at the base of
the neck. Slowly lift the clipper, working upwards
and outwards through the hair, trimming just a
little at a time.
Back of the head (Diagram B): Set the comb
position at 12mm or 17mm, cut the hair at the
back of the head.
Side of the head (Diagram C): Set the comb
position between 3mm and 6mm, trim sideburns.
Then change to the longer setting (12 or 17mm)
and continue to cut to the top of the head.
Top of the head (Diagram D): Set the comb
position between 17mm and 22mm cut hair on
top of the head against the direction in which
the hair normally grows. To make longer hair on
top, use the appliance without comb attachment.
Lift the hair on top of the head with a small hand
comb. Cut over the hand comb with the hair
lifted or hold the hair between the fingers to lift
it and cut it to the desired length. Always work
from the back of the head.
The finishing touches (Diagrams E, F & G ): Use
the clipper without an attachment comb for close
trimming around the base and sides of the neck.
To produce a clean straight line at the sideburns,
reverse the hair clipper. Place the reversed
clipper at right angles to the head, tips of the
blades lightly touching the skin and then work
downwards.
Comb
position
1
2
3
4
5
6
7
Small cutting
comb
2 mm
5 mm
8 mm
11 mm
14 mm
17 mm
20 mm
Large cutting
comb
22 mm
25 mm
28 mm
31 mm
34 mm
37 mm
40 mm
… 10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fakir BOSS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fakir BOSS in the language / languages: English, Turkish as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info