752947

Faber Agtrim - Agio Manual

1
Zoom out
Zoom in
Previous page
1/1
Next page
Three Screws
Rangehood Body
Front
Strip
CUSTOMIZING YOUR RANGEHOOD
The front strip of the rangehood can be customized by replac-
ing the factory supplied strip with a custom front strip made
from the same materials as your cabinets. The front strip is
attached to the rangehood by three recessed screws and
three key hole slots on the back side of the strip as indicated
in FIGURE 1. It is necessary only to remove the three lower
screws to remove the front strip. The top screws will slide out
of the key holes once the three lower screws are removed.
Side View of the Rangehood
The front strip dimensions are given in FIGURE 2. For a
custom front strip, a local cabinet shop can make a strip to
match your cabinets. If you wish to keep the frame of the front
panel and only replace the glass panel, the dimensions follow:
Height = 5 11/16", Depth = 1/8", Width = 29 11/16" (for 30"
model) 35 11/16" (for 36" model) 23 5/8" (for 24" model).
FIGURE 1
23 5/8" or 29 15/16" or 35 15/16"
Vue latérale de la hotte
FIGURE 2
PERSONNALISER LA HOTTE
La bande frontale de la hotte peut être personnalisée en
remplaçant la bande fournie par une bande de même
matière que l’armoire. La bande frontale est maintenue à
la hotte par trois vis creuses et trois fentes à l’arrière de la
bande comme il est indiqué à la FIGURE 1. Les vis du des-
sus glisseront hors des fentes lorsque les trois vis creuses
seront enlevées.
Les dimensions de la bande sont données à la FIGURE 16.
Pour une bande personnalisée, un marchand d’armoires
peut fabriquer une bande qui s’assortira aux armoires. Si
vous désirez retenir la charpente de la bande frontale, et
seulement replacer le verre, les dimensions sont Hauter =
5 11/16 po, Épaisseur = 1/8 po, Largeur = 29 11/16" (pour
modèle 30 po) 35 11/16 po (pour modèle 36 po) 23 5/8 po
(pour modèle 24 po).
Bande
frontale
Boîtier de la hotte
Trois vis
FIGURE 1
23 5/8" or 29 15/16" or 35 15/16"
FIGURE 2
Agio - Instructions for customizing the front face plate
Agio - Instructions pour personnaliser le plat de visage avant


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Faber Agtrim - Agio at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Faber Agtrim - Agio in the language / languages: English, French as an attachment in your email.

The manual is 0,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info