626606
1
Zoom out
Zoom in
Previous page
1/4
Next page
1 1
FAAC XT2-XT4 868 SLH
I - XT2 cod. 787005 XT4 cod. 787006
DESCRIZIONE ETICHETTA ( Figura 2 )
A - Codice identificativo del modello
B -
Numero identificativo del lotto di produzione
C - Leggere le istruzioni
D - Smaltire secondo le direttive vigenti
E - Riferimento notified body
P1
P3
P4
P2
Frequenza di lavoro
868.92 MHz ±100KHz
Tipo batteria 2pile litio3V CR2032
Uso esclusivo
Apricancello
Questo prodotto è conforme alla direttiva
99/05/CEE
1
2
A
B
C
E
D
+
RICONOSCERE UN Tx MASTER/SLAVE
•master : premendo qualsiasi tasto di un TX master,
il led effettua un lampeggio prima di accendersi a
luce fissa.
•slave : premendo qualsiasi tasto di un TX slave, il
led si accende subito a luce fissa.
SEQUENZA DI PROGRAMMAZIONE
1)Alimentare l’impianto dopo aver effettuato l’instal-
lazione ed i collegamenti elettrici dei componenti
del Sistema 868 SLH.
2)Utilizzare un Tx master per impostare il “codice im-
pianto” sulla scheda decodifica/ricevente RP (vedi
“codifica impianto”).
3)Utilizzare lo stesso Tx master per impostare il codice
impianto sugli altri Tx dell’impianto (vedi “codifica
Tx”).
4)I Tx codificati verranno memorizzati automatica-
mente nella scheda decodifica/ricevente RP sempli-
cemente attivando due volte in successione, entro
max 5 secondi, il canale del trasmettitore.
CODIFICA IMPIANTO
•Premere contemporaneamente i pulsanti P1 e P2
del Tx master e rilasciarli quando il led lampeggia
(dopo circa un secondo);
•Sulla scheda decodifica/ricevente RP, premere e
mantenere premuto il pulsante di apprendimento:
il led deve lampeggiare;
•Sul Tx master (mentre il suo led sta ancora lampeg-
giando), premere e mantenere premuto un canale
(il led del trasmettitore si accende a luce fissa);
•Sulla scheda decodifica/ricevente RP, verificare
l’accensione fissa del led per un paio di secondi,
a conferma dellavvenuta memorizzazione del
“codice impianto”, prima di rilasciare il pulsante di
apprendimento;
•Rilasciare il pulsante del canale del Tx master.
CODIFICA TX
•Premere contemporaneamente i pulsanti P1 e P2
del Tx master utilizzato per la codifica impianto, e
rilasciarli quando il led lampeggia (dopo circa un
secondo);
•Accostare frontalmente a contatto il Tx master al
Tx da codificare (master o slave);
•Sul Tx master (mentre il suo led sta ancora lampeg-
giando), premere e mantenerepremuto lo stesso
canale utilizzato per la codifica impianto: il led si
accende a luce fissa;
•Sul Tx da codificare, premere il canale desiderato
e rilasciarlo quando il led si spegne dopo un doppio
lampeggio, a conferma dell’avvenuta memorizza-
zione del “codice impianto”;
•Rilasciare il pulsante del canale del Tx master;
•Ripetere la stessa procedura per ogni Tx da
codificare.
DESCRIPTION OF THE LABEL (Fig. 2 )
A - Model identification code
B –
Identification number of the production batch
C – Read the instructions
D –
Observe the current regulations for a correct disposal
E – Notified body reference
Work frequency
868.92 MHz ±100KHz
Battery type 2 X CR2032 3V lithium batt.
Intended use Gate opener
This product conforms to directive 99/05/EEC
_
Via Calari, 10 - 40069 Zola Predosa (BO) - ITALY - Tel. +39.051.61724 - www.faacgroup.Com
GB - XT2 cod.787005 XT4 cod.787006
The complete CE Declaration can be downloa-
ded from www.faacgroup.com
CAUTION:
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS.
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for FAAC XT4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of FAAC XT4 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info