811702

Extraflame ANNABELLA AD EVO Manual

34
Zoom out
Zoom in
Previous page
1/36
Next page
34 ENGLISH
Displays
Display Reason
off Generator o
sTaRT The start-up phase is in progress
pelleT loaDinG Continuous pellet feeding is in progress during the ignition phase
iGniTion The ignition phase is in progress
pRepaRaTion The preparation phase is in progress
WoRK The normal work phase is in progress
MoDUlaTion The generator is working at minimum
final CleaninG The nal cleaning is in progress
sTanD By Generator o waiting for re-ignition due to the external thermostat.
CoolinG
sTanD By
A new ignition is attempted when the generator has just been switched o. When the generator switches o, you must
wait for the complete shutdown of the fumes motor, then clean the burn pot. The generator can only be re-ignited when
these operations have been performed.
BlaCK oUT
sTanD By
The generator is cooling after a power cut.
Once cooling is completed, it will re-start automatically
aUTo BloW The automatic blow is active
Close
HoppeR-sToVe DooR
This indication means that you have 60 seconds to close the hatch/door and the pellet lid.
After 60 seconds have passed, the stove will enter “DEPR ALARM” during the ignition phase, while during normal
operation, the stove will enter "COOLING STAND BY" and then restart automatically when the conditions are met (cold
stove, etc.).
alaRMs
Display eXplanaTion solUTion
Indicates the presence of an alarm.
On: indicates the presence of an alarm
The alarm can only be reset if the fumes motor has stopped and 15
minutes have passed since the alarm was displayed, by pressing key 1
for 3 seconds.
fUMes MoToR
faUlT Fumes motor fault Contact after-sales centre
fUMes pRoBe Fumes probe fault. Contact after-sales centre
HoT fUMes High fumes temperature Check pellet loading (see "Easy setup"); if the problem is not solved,
contact a service centre.
no
iGniTion
The pellet hopper is empty.
Pellet feed calibration inadequate.
Thermostat bulbs tripped.
Check for the presence of pellets in the hopper.
Adjust the pellet ow (see “Easy setup”).
Check the procedures described in the “Ignition” chapter.
Check bulb thermostats (see chapter on Resetting)
no flaMe
The pellet hopper is empty.
No pellet feed.
The gearmotor does not feed pellets.
Thermostat bulbs tripped.
Check for the presence of pellets in the hopper.
Adjust the pellet ow (see “Easy setup”).
Check bulb thermostats (see chapter on Resetting)
DepR alaRM
The door is not closed correctly.
The ash drawer is not closed correctly.
The combustion chamber is dirty.
The fumes exhaust pipe is blocked/dirty
Check hermetic door closure.
Check hermetic closure of the ash drawer.
Check cleanliness of the fumes pipe and the combustion chamber.
no
iGniTion - BlaCK oUT
No power during the ignition
phase.
Turn the stove off using key 1 and repeat the procedure described in
the "Ignition" chapter.
Other reset operations should be performed by an authorised
technician.
CoMManD aUGeR
alaRM Abnormal pellet feeding. Contact the after-sales centre.
aUGeR BloCKeD Abnormal operation of pellet motor. Contact the after-sales centre.
… 34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Extraflame ANNABELLA AD EVO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Extraflame ANNABELLA AD EVO in the language / languages: English as an attachment in your email.

The manual is 7.16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Extraflame ANNABELLA AD EVO

Extraflame ANNABELLA AD EVO User Manual - German - 36 pages

Extraflame ANNABELLA AD EVO User Manual - Dutch - 36 pages

Extraflame ANNABELLA AD EVO User Manual - French - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info