540695
17
Zoom out
Zoom in
Previous page
1/24
Next page
17
STORAGE
Before clearing the machine away, the water must be removed from the pump, the hose and the
accessories. You do this by switching the machine off with the switch and disconnecting the water
supply hose. Now start the machine again and squeeze the handle. Allow the machine to operate
until no more water comes out of the jet lance. Then switch the machine off immediately. Never allow
it to ’run dry’!
Remove the plug from the socket, wind the hose up and hang the cable on the hook.
Place the handle and the lances in the holders on the machine.
The machine must be stored frost-free. If this is impossible, have the machine suck in anti-freeze
before you store it. Remember to flush the machine thoroughly with water before using it again! If the
machine nevertheless freezes, have it checked before use. Frost damage is not covered by the
guarantee. Never start a frozen high-pressure cleaner!
SAFETY FEATURES
The nozzle is fitted with a ‘lock’ for safety. If you push the button to the left, the handle is locked and will
not function. Unlock the handle by pushing this switch back to the original position.
The motor is fitted with a thermal safety feature that switches it off when it overheats. In principle, it will
start again automatically when it is sufficiently cooled. But it is better to switch the machine off for 5 to 10
minutes, wait, and then start it again. Identify the cause of the overheating and remove it. If this problem
recurs, stop using the machine and contact your supplier / repair service.
MAINTENANCE
Attention: Always take the plug out of the socket before you execute maintenance!
Flush the water supply hose, the high-pressure hose, the jet lance, the nozzle and other accessories
thoroughly before you use them.
Carefully remove dust, sand or other dirt from the connections.
Thoroughly rinse and clean the accessories that you have used for spraying.
Regularly clean the nozzle with the pin supplied and then flush it thoroughly (against the direction of
the jet). To do this you must remove the nozzle from the lance.
Regularly clean the filter in the water inlet. To do this, unscrew the water inlet connector, remove the
filter with a little pincers or similar tool and check that it is undamaged. Fasten everything firmly and
correctly in the appropriate place. Never use the cleaner without a filter!
Keep the ventilation openings of the machine clean in order to prevent obstruction of the cooling
function.
Regularly grease the O-rings of the connectors in order to prevent them from drying out.
Repairs and inspections must only be carried out by your supplier or appropriately trained and
authorised persons. Inexpertly executed repairs will nullify the guarantee.
Never carry out repairs yourself!
RECYCLING
Your high-pressure cleaner is not normal household waste. When you finish using it, take it to a waste
collection point designated by your local council.
PROBLEMS AND SOLUTIONS
The machine does not start
- Is the plug inserted into the socket?
- Is the socket not in good working order? Try another.
- Is the fuse burnt out? Replace it.
- Extension cable broken. Use another cable.
The pressure fluctuates
- The pump is sucking air in. Seal the connections correctly.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eurom Force 2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eurom Force 2000 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info