571324
19
Zoom out
Zoom in
Previous page
1/24
Next page
Instruction for use CALLISTO
19
© ETNA Coffee Technologies b.v.
COFFEE TECHNOLOGIES
Make sure the pump cup is properly in place. Incorrect
assembly may cause incorrect dosing of product.
7. Push the spout into the hose of the peristaltic pump.
8. Slide the hose lock off the hose of the BIB so that the hose is no
longer closed.
9. Switch the machine on at the on/off switch.
10.Place a jug under the dispensing nozzle.
11.Press button 3 on the service panel on the inside of the door. Keep
this button pressed until the hose of the peristaltic pump is
completely filled.
12.Press button 1 on the service panel on the inside of the door. The
mixer will be rinsed with hot water.
13.Repeat step 12 until the mixer is clean.
14.Close the cover and the door of the machine.
7.2.2.2 Cleaning the peristaltic pump for BIB with QCD connector
1. Open the door and lift the cover of the machine.
2. Switch the machine off at the on/off switch.
3. Open the QCD connector by pulling the inner part with the hose
connectors to the outside. The connector is fully opened when the
word “OUT” is visible on the inner part (see paragraph 5.4.2).
4. Detach the QCD connector from the pump hose.
5. Lower the clamp securing the pump cup.
6. Take the pump cup with hose out of the housing.
7. Clean the hose in the pump cup, the non-drip spout and the QCD
connector with hot water.
8. Clean the rotor assembly with a damp cloth.
9. Put the pump cup back in place.
10.Move the clamp over the pump cup.
Make sure the pump cup is properly in place. Incorrect
assembly may cause incorrect dosing of product.
11.Reconnect the QCD connector to the pump hose.
12.Slide the QCD connector on to the connector of the BIB.
13.Assemble the QCD connector by pushing in the inner section with
the hose connectors. The connector is fully home when the marker
on the hose connectors and the outer section of the QCD connector
are directly opposite one another .
14.Switch the machine on at the on/off switch.
Figure 7-2 Placing the pump cup on the peristaltic pump
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Etna CALLISTO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Etna CALLISTO in the language / languages: English as an attachment in your email.

The manual is 0,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info