74242
36
Zoom out
Zoom in
Previous page
1/38
Next page
71 INSTALLATION GUIDE
2 lives with 2 neutrals connection
(2 2N a.c. 230 V / 50 Hz):
The voltage between live and neutral is 230 V
a.c. There may be a voltage of 0 V between
the phases if they are connected to the same
phase in the meter cupboard but also 400 V if
they are connected to 2 different phases. Your
groups must be fused with at least 16 A (2x).
The connecting power cable must have a
minimum core cross section of 2,5 mm
2
.
2 lives with 1 neutral connection
(2 1N a.c. 400 V / 50 Hz):
The voltage between the phases and the
neutral is 230 V a.c. Between the lives there is
a voltage of 400 V. If there is not a voltage of
400 V between the lives, two wires have been
taken from the same live in the meter
cupboard and the hob must be connected
with two neutral wires, as indicated above
under 2 lives with 2 neutrals. Install a
connecting bridge between the connection
points 4-5.
Your groups must be fused with at least 16 A
(2x). The connecting power cable must have a
minimum core cross section of 2,5 mm
2
.
3 lives with 1 neutral connection
(3 1N a.c. 400 V / 50 Hz):
The voltage between the phases and the
neutral is 230 V a.c. There is a voltage of 400 V
between the lives. Fit a connecting bridge
between the connection points 4-5. Phase 3
carries no load. Your groups must be fused
with at least 16 A (3x). The connecting power
cable must have a minimum core cross
section of 2,5 mm
2
.
right front
left front
left rear
right rear
appliance
internal
right front
left front
left rear
right rear
appliance
internal
right front
left front
left rear
right rear
appliance
internal
70
Built in T200
Electrical connection
For the connection, use an approved cable,
in accordance with the regulations. The
cable casing should be of rubber..
There is a label on the underside of the
appliance with the wiring diagrams. The
connection terminals are accessible once
you have opened the junction box on the
underneath. The junction box cover can be
opened with a screwdriver.
If you want to make a fixed connection,
make sure that a multi-polar switch with a
contact separation of at least 3 mm is fitted
in the supply line.
Power setting table
The appliance can be connected in the
following ways:
1 phase connection (1 1N a.c. 230 V / 50 Hz):
The voltage between live and neutral is
i230 V a.c. Install connecting bridges between
connection points 1-2 and 4-5.
Your group must be protected by a fuse of at
least 32 A. The connecting power cable must
have a minimum core cross section of 6 mm
2
.
INSTALLATION GUIDE
Type of hob T200
Connection
230 V - 50 Hz x
Power of elements
Front left 2300 W
Rear left 1200 W
Rear right 2000 W
Front right 1200 W
right front
left front
left rear
right rear
appliance
internal
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Etna A 565 A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Etna A 565 A in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info