Manual Etna 4182 (page 3 of 6) (English, German, Dutch, French)

109460

Zoom out

Zoom in

1/6

ENGLISH

GENERAL

Carefully read the following important information regarding installation

safety and maintenance. Keep this information booklet accessible for

further consultations.

The appliance has been designed as a exhausting version (external

exhaust) or as a filter version (internal air recycle) cooker hood.

SAFETY PRECAUTION

1. ake care when the cooker hood is operating simultaneously with an

open fireplace or burner that depend on the air in the environment and

are supplied by other than electrical energy, as the cooker hood removes

the air from the environment which a burner or fireplace need for

combustion.

The negative pressure in the environment must not exceed 4 Pa (4 x

10 -5 bar).

Provide adequate ventilation in the environment for a safe operation of

the cooker hood.

Follow the local laws applicable for external air evacuation.

2. WARNING!!

In certain circumstances electrical appliances may be a danger

hazard.

A) Do not check the status of the filters while the cooker hood

is operating

B) Do not touch the light bulbs after appliance use

C) Flambè cooking is prohibited underneath the cooker hood

D) Avoid free flame, as it is damaging for the filters and a fire

hazard

E) Constantly check food frying to avoid that the overheated oil

may become a fire hazard

F) Disconnect the electrical plug prior to any maintenance.

INSTALLATION INSTRUCTIONS

• Electric Connection

The appliance has been manufactured as a class II, therefore no earth

cable is necessary.

The connection to the mains is carried out as follows:

BROWN = L line

BLUE = N neutral

If not provided, connect a plug for the electrical load indicated on the

description label. Where a plug is provided, the cooker hood must be

installed in order that the plug is easily accessible.

An omnipolar switch with a minimum aperture of 3mm between

contacts, in line with the electrical load and local standards, must be

placed between the appliance and the network in the case of direct

connection to the electrical network.

• The appliance must be installed at a minimum height of 650 mm from

an cooker stove.

If a connection tube composed of two parts is used, the upper part must

be placed outside the lower part.

Do not connect the cooker hood exhaust to the same conductor used

to circulate hot air or for evacuating fumes from other appliances

generated by other than an electrical source.

• ATTENTION: should the lamps not work, make sure they are well

tightened.

• MOUNTING OF THE HOOD IN THE LOWER PART OF AN

HANGING CUPBOARD

Drill 4 holes of 6 mm. diameter at the bottom of the hanging cupboard

as showed in the drawing fig.3.

Fit the hood in the cabinet with 4 screws, which are appropriate to that

kind of cupboard.

The appliance is provided with 2 air outlets, one which is in the upper

part and the other on the back. Both of them can be used according to

your requirements. A connecting ring (C), which to join the connecting

pipe to,and a cover (A) to close the air outlet, which is not used, are

supplied.

• MOUNTING OF THE HOOD IN THE WALL

Make 4 holes (B-P) according to the measurements indicated in fig. 2.

For the various assembly operations, use screws and anchors suitable

for the type of wall (eg., concrete, plasterboard, etc.)

Hang the hood on the wall using the two holes (B) fig. 2.

Secure the hood to the wall using the two lower safety holes (P).

• MOUNTING OF THE HOOD ON THE WALL

Drill 2 holes on the wall, which correspond to the position (B) of the

drawing fig. 1.

Hang the hood on the 2 holes by using the screws and dowels with

expanding plug ,which are aprropriate for that kind of wall (ex.

concrete, plasterboard etc.)

Fix definitely the hood through the 2 security holes (Z).

• FITTING THE PIPES (OPTIONAL)

Make four holes (G-H) according to the measurements indicated in

fig. 2

For the various assembly operations, use screws and anchors suitable

for the type of wall (eg., concrete, plasterboard, etc.)

Secure the bracket (Z) to the wall fig. 2

Position the two pipes vertically on the hood.

Hang the pipe fitting (F) using the 2 holes (H) fig. 2

Remove pipe fitting (E) from fitting (F) and secure to the side of the

bracket (Z) with the screws provided.

• FITTING THE GLASS SECTION (OPTIONAL)

Position the glass section complete with supports (V) as indicated in

fig. 1 and secure to the hood using the screws provided.

• FITTING THE HANDLE (OPTIONAL)

Position the handle (M) and the two right (D) and left (S) supports, as

indicated in fig. 1, and secure to the hood using the screws provided.

• CHANGING FROM EXHAUSTING HOOD TO FILTERING ONE

In order to make this change (possible also after the use of the

exhausting system), demand a set of carbon filters to your dealer.

Active carbon filters are necessary to depurate the air, that will be

released in the room. Filters are not washable; they cannot be

regenerated and have to be replaced at most every 4 months. The

saturation of the activated charcoal depends on the more or less

prolonged use of the hood, on the type of cooking and on the regularity

of cleaning the grease filter. The filter (C) has to be applied to the

aspirating group, which is inside the hood hiting the centre of the group

with it and turning it of 90 degrees until the stop click is heard to lock

it. Remove the grill (G) to carry out this operation. Close with the

appropriate covers the upper and back air outlets; turn the small lever

(L) from the position (A) to the position (F). In this way the hood is

ready for the filtering function.

USE AND MAINTENANCE

• It is recommended to operate the appliance prior to cooking.

It is recommended to leave the appliance in operation for 15 minutes

after cooking is terminated in order to completely eliminate cooking

vapours and odours.

The proper function of the cooker hood is conditioned by the regularity

of the maintenance operations, in particular, the active carbon filter.

• The anti-grease filters capture the grease particles suspended in the

air, and are therefore subject to clogging according to the frequency of

the use of the appliance.

In order to prevent fire hazard, it is recommendable to clean the filter

at a maximum of 2 months by carrying out the following instructions:

- Remove the filters from the cooker hood and wash them in a solution

of water and neutral liquid detergent, leaving to soak.

- Rinse thoroughly with warm water and leave to dry.

- The filters may also be washed in the dishwasher.

The aluminium panels may alter in colour after several washes. This

is not cause for customer complaint nor replacement of panels.

• The active carbon filters purify the air that is replaced in the

environment. The filters are not washable nor re-useable and must be

replaced at maximum every four months. The saturation of the active

carbon filter depends on the frequency of use of the appliance, by the

type of cooking and the regularity of cleaning the anti-grease filters.

• Clean the fan and other surfaces of the cooker hood regularly using

a cloth moistened with denatured alcohol or non abrasive liquid

detergent.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR

EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE

WARNINGS.

ENGLISH

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Etna 4182 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,04 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Etna 4182 Manual

Product: