700326
5
Zoom out
Zoom in
Previous page
1/8
Next page
5
ENGLISH
POWER RATING
The ESX VISION VE subwoofer enclosures are designed for high bass levels. Anyhow it is possible,
that unsatisfying sound characteristics could be caused by too low or too high amplier power. In
certain circumstances this even can cause a damage to the loudspeakers.
It is recommended to choose rather a more powerful amplier (ca. 15-20% more Watts RMS than
the max. RMS power rating of the woofer) and to use the amplier not at the maximum output level
(low distortion factor, good sound characteristics). A weaker amplier at the maximum level causes
worse sound characteristics due to the higher distortion factor.
Never crank up the output volume of your amplier to the maximum level or run the amplier into
the clipping range. If the sound is distorted and not clean, turn back the level until the distortions
disappear.
Please note the following recommended power ratings:
VE200
One Amplier with approx. 240 to 360 Watts RMS @ 4 Ohms.
VE250
One Amplier with approx. 300 to 500 Watts RMS @ 4 Ohms.
VE300
One Amplier with approx. 350 to 600 Watts RMS @ 4 Ohms.
The ESX VISION VE subwoofer enclosures have no integrated limiter or clipper, which is limiting
the level upwards. Overamplied bass peaks leads inevitably to a burn out of the voice coil of the
woofer. A burn out of the voice coil, caused by clipping/overamping is not covered by the usual
warranty.
LED-ILLUMINATION
The ESX VISION VE subwoofer enclosures have an integrated LED-illumination. This illumination
is only allowed to light up, if the vehicle is not in driving condition. It is recommended to switch the
illumination with the vehicle‘s trunk illumination. To power-up the LED-illumination, use the supplied
wiring harness, which should be plugged into the integrated socket (12V DC) of the speaker ter-
minal.
Connect the marked “+” cable with the +12 volts line and the marked “–” cable with the ground line
of the vehicle´s trunk illumination. Please ensure that the connection of the cables have the correct
polarity as marked.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ESX VE250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ESX VE250 in the language / languages: English, German as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info