700323
2
Zoom out
Zoom in
Previous page
1/2
Next page
DISTRIBUTION:
Audio Design GmbH · Am Breilingsweg 3 · D-76709 Kronau / Germany
Fon +49 7253 - 9465-0 · Fax +497253 - 946510 · www.audiodesign.de
QSB6 · QSB8 · QSB10
BELASTBARKEIT
Die ESX QUANTUM Gehäuse-Subwoofer sind auf laute Basspegel ausgelegt. Dennoch ist bei einer zu niedrigen
oder zu hohen Verstärkerleistung kein zufriedenstellendes Klangbild erreichbar. Dies kann unter Umständen
sogar zu einer Beschädigung der Lautsprecher führen. Es ist empfehlenswert eher einen kräftigeren Verstärker
(ca. 15-20% mehr Watt RMS als die maximale RMS Belastbarkeit des Woofers) zu wählen, und diesen nicht bei
voller Lautstärke zu spielen (geringer Klirrfaktor, guter Klang). Ein schwächerer, voll ausgepegelter Verstärker
führt zu einem schlechteren Klangbild aufgrund des höheren Klirrfaktors. Drehen Sie die Lautstärke Ihres
Verstärkers nie bis zum Anschlag auf bzw. soweit, dass der Verstärker in den Überlastbereich (Clipping) kommt.
Falls das Klangbild verzerrt bzw. übersteuert oder unsauber ist, drehen Sie die Lautstärke so weit zurück, bis
keine Verzerrungen mehr zu hören sind.
Beachten Sie dazu die empfohlenen Wattangaben:
QSB6 ca. 200 bis 300 Watt RMS (Sinus)
QSB8 ca. 300 bis 500 Watt RMS (Sinus)
QSB10 ca. 500 bis 700 Watt RMS (Sinus)
Bitte beachten Sie, dass ein verringerter Impedanzwert eine Leistungssteigerung des Verstärkers zur Folge hat.
Diese Leistungssteigerung kann auch verstärkt zu Clipping führen. Dies geschieht z.B. wenn mehrere Lautspre-
cher parallel an den Verstärker angeschlossen werden. Beachten Sie zudem die Mindestimpedanz des
verwendeten Verstärkers. Wenden Sie sich im Zweifelsfall an ihren Fachhändler.
ACHTUNG
Die Gehäuse-Subwoofer besitzen keinen Limiter oder Begrenzer, der den Pegel nach oben begrenzt. Übersteuer-
te Basspegel führen unweigerlich zu einem Durchbrennen der Schwingspulen des Woofers. Durch Clipping/Über-
steuerung verursachte Verbrennungen der Schwingspulen fallen nicht unter die übliche Garantieleistung.
WICHTIGE HINWEISE
Wählen Sie für die Installation eine Position im Fahrzeug, bei der weder das Sichtfeld des Fahrers, noch die
Sicherheit der Insassen beeinträchtigt wird. Dies gilt besonders für Airbag-Zonen und Sicherheitsgurte. Die
permanente Temperatur des Einbauortes sollte 5°C nicht unterschreiten bzw. 50°C nicht überschreiten. Schützen
Sie zudem das Gerät vor Nässe und Feuchtigkeit.
Stellen Sie auch sicher, dass sich das Gerät während der Fahrt nicht lösen kann bzw. jemand im Fahrgastraum
verletzen kann. Es wird empfohlen, das Soundsystem wenn möglich mit Spanngurten oder ähnlichen Befesti-
gungsarten im Kofferraum zu befestigen.
Achten Sie bei der Installation und der Befestigung des Geräts unbedingt darauf, dass keine serienmäßige
Komponenten des Fahrzeugs (Airbags, Sicherheitsgurte, Kabelstränge, Benzintank etc.) durch Bohrlöcher oder
ähnliches beschädigt werden.
Schrauben Sie bitte keine anderen Geräte wie z.B. Verstärker auf das Gehäuse. Dadurch könnte die Elektronik
beschädigt werden.
In Ihrem eigenen Interesse sollte die Lautstärke des Soundsystems so gewählt werden, dass die Verkehrsfähig-
keit und die Konzentration des Fahrers nicht beeinträchtigt wird, um Verkehrsgeräusche und akustische
Warnsignale noch hören zu können.
Moderne Car Audio Soundsysteme produzieren enormen Schalldruck jenseits der 100 dB Grenze. Beachten Sie
dazu, dass dauerhafter Gebrauch Ihr Hörvermögen bei sehr hohen Lautstärken nachhaltig schädigen könnte.
Bitte beachten Sie unbedingt die korrekte Polung der Anschlüsse. Falsch installierte oder angeschlossene Geräte
können Ihr Fahrzeug und das Gerät selbst dauerhaft beschädigen.
Verbinden Sie niemals die Lautsprecher-Anschlüsse mit der 12 Volt Leitung, da sonst die Lautsprecher zerstört
werden können.
POWER RATING
The ESX QUANTUM subwoofer enclosures are designed for high bass levels. Anyhow it is possible, that
unsatisfying sound characteristics could be caused by too low or too high amplifier power. In certain circumstan-
ces this even can cause a damage to the loudspeakers. It is recommended to choose rather a more powerful
amplifier (ca. 15-20% more Watts RMS than the max. RMS power rating of the woofer) and to use the amplifier
not at the maximum output level (low distortion factor, good sound characteristics). A weaker amplifier at the
maximum level causes worse sound characteristics due to the higher distortion factor. Never crank up the output
volume of your amplifier to the maximum level or run the amplifier into the clipping range. If the sound is distorted
and not clean, turn back the level until the distortions disappear.
Please observe the following recommended power ratings:
QSB6 an output power of approx. 200 up to 300 Watts RMS (Sinus).
QSB8 an output power of approx. 300 up to 500 Watts RMS (Sinus).
QSB10 an output power of approx. 500 up to 700 Watts RMS (Sinus).
Please observe, that a lower impedance operation causes a higher output power of your amplifier. This increasing
could cause that the amplifier run into the clipping range. This events when more loudspeakers are connected in a
parallel-operation-circuit to the amplifier. Please observe the minimum impedance of the installed amplifier. In
case of doubt ask your dealer.
CAUTION
The subwoofer enclosures have no integrated limiter or clipper, which is limiting the level upwards. Overamplified
bass peaks leads inevitably to a burn out of the voice coil of the woofer. A burn out of the voice coil, caused by
clipping/overamping is not covered by the usual warranty.
IMPORTANT NOTES
Choose a suitable location for your soundsystem, that neither the driver’s field of vision nor the security of the
inmates will be affected. This stands also for airbag-zones and safety belts. The permanent temperature of the
location should not be lower than 5°C and not higher than 50°C. Protect the device from moisture and humidity.
Ensure that your subwoofer enclosure will not get loose during the drive and hurt someone in the passenger
cabin. It is recommended, that you mount the subwoofer enclosure with suitable belts or any other mounting
solutions in the trunk area.
Please observe that you don’t damage any serial components of your vehicle (airbags, wires, gastank etc.) during
the installation of your soundsystem by drilling or any other operations.
Never screw or mount any other devices (amps, caps etc.) onto the subwoofer enclosure, this may cause damage
to the electricity.
For your personal concerns you should choose a appropriate sound level for the subwoofer enclosure, that
neither the roadworthy of the driver nor his concentration will be disturbed, that he is able to notice possible traffic
noises and acoustical warning signals.
Modern car audio soundsystems provide very high acoustic pressure beyond the 100 dB mark. Please observe in
this case, that permanent use of high sound levels may cause damage to your ability of hearing.
Please ensure by any means the correct polarity of all connections. Faulty installed and connected devices may
get damage the vehicle and the device permanently.
Never connect the speaker terminals with the 12 Volt power supply, otherwise the speakers may get damaged.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ESX QSB8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ESX QSB8 in the language / languages: English, German as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info