500134

Eltax Home Cinema 1 Manual

2
Zoom out
Zoom in
Previous page
1/18
Next page
2
Instruction manual
May we start by thanking you for purchasing Eltax loudspeakers. You have just purchased one of the best domestic hi
loudspeakers available and we hope you will enloy the music they reproduce for many years to come. The following
notes are designed to assist you in obtaining a greater degree of musical satisfaction from your Eltax loudspeakers.
Before connecting your loudspeakers, we suggest that you read this leaets carefully.
Amplier compability/power handling
Your Eltax loudspeaker system will operate satisfactorily with any good amplier designed for use with an 4-8 Ohm
impedance load. Allthough Eltax loudspeakers are designed to handle high power loadings, you must remember
that any loudspeaker that is abused with excessive use of volume, tone controls and graphic equalisers is likely to
cause damage to the drive-units. Be carefull especially with small ampliers constantly driven on high power levels
as these may be liable to go into »clipping mode« and disort the signal causing possible damage. If you hear a
distorded signal through the loudspeakers you must reduce the power level.
Connecting to your amplier
We strongly recommend the use of high quality speaker cables, colour coded or grooved cables are recommended
to assist checking polarity, your local dealer should be able to advise you on this point. Always switch OFF your
amplier before making any connections or adjustments to the system. Wire the right-hand channel cable so that
the positive terminal of your loudspeaker is connected to the positive on your amplier, and the negative terminal of
your loudspeaker is connected to the negative terminal on your amplier. Repeat the instructions for all channels.
Do NOT connect more than one loudspeaker to one terminal on your amplier.
Phasing
Providing that you have followed the connecting instruction correctly the loudspeakers should be in phase and
provide solid stereo images. If, however, you have any doubt as to the phasing of the loudspeakers, try reversing
the connections to ONE of the loudspeakers, and play a recording which has plenty of deep bass operating both
loudspeakers simultaneously with the stereo amplier switched to »mono«. The correct polarity is indicated by rm
full bass, when incorrect, the bass will be noticeably much weaker.
Service
No routine attention is required to the working parts of the loudspeakers and being very reliable Eltax loudspeakers
rarely require service. Any service problems should in the rst instance be referred to your dealer.
Betriebsanleitung
Wir danken Ihnen, dass Sie Eltax Lautsprecherboxen gekauft haben. Wir sind sicher, dass Sie diese
Lautsprecherboxen viele Jahre geniessen werden. Die folgenden Anweisungen sollen Ihnen helfen, den
höchsten Genuss Ihrer Boxen zu sichern.
Power handling
Ihre Eltax Lautsprecherboxen können Sie an jedem guten Verstärker mit 4 oder 8 Ohm anschliessen. Sie
sollten wissen, dass Verstärker mit kleiner Wattleistung, die standig mit voller Leistung betrieben werden,
eher Schaden an den Lautsprechern verursachen als Verstärker, die eine hohe Wattleistung haben. Der
Grund ist, dass kleine Verstärker, die unrealistisch hoch betrieben werden, möglicherweise eine »Clipping«
Phase erreichen und so verzerrte Signale an die Lautsprecher weiterleiten. Es kann dabei zu einer Zerstörung
der Lautsprecher kommen.
Deshalb
Wenn Sie ein verzerrtes Signal aus Ihren Lautsprechern hören, sollten Sie sofort Ihr »Power Volumen«
ruedriger stellen.
Kabel
Schalten Sie bitte den Verstärker aus, bevor Sie die Kabel verbinden. Verbinden Sie den rechten Kanal so,
dass das rote Klemmanschluss am Lautsprecher mit dem roten Verstärker-Anschluss verbunden wird. Dann
verbinden Sie den schwarzen Klemmanschluss am Lautsprecher mit dem Schwarzen Anschluss am Verstärker.
Für den Linken Kanal wiederholen Sie den Vorgang wie oben beschrieben. Verbinden Sie nicht mehr als eine
Lautsprecherbox pro Verstärker-Anschluss.
Kundendienst
Keine regelmässige Inspektion der beweglichen Teile ist erforderlich. Nur in seltenen Fällen wird es notwendig
2 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eltax Home Cinema 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eltax Home Cinema 1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info