483275
31
Zoom out
Zoom in
Previous page
1/34
Next page
-29-
-36-
Scroll through the menu until ‘2-1 Alarm Time’ is displayed. The current
setting will also be displayed. To change the setting press .
Enter the required alarm duration in units of 10s.e.g. enter 6 for a 60s alarm
duration (max setting 60, i.e. 600s/10mins).
Press to save and exit, or
Press to exit without saving.
Note: Following initiation of a Full Alarm condition the External Siren will
continue to sound until either the system is disarmed; or the Control Panel
Alarm Duration Time expires.
Press to return to top level System Setup menu.
INTERNAL SIREN
Default setting: ON
Scroll through the menu until ‘2-2 INT. Siren’ is displayed. The current setting
will also be displayed.
To change the setting press .
Press to enable the Siren, or
Press to disable the Siren.
EXTERNAL HARDWIRED SIREN
Default setting: ON
Scroll through the menu until ‘2-3 EXT. Siren’ is displayed. The current setting
will also be displayed.
To change the setting press .
Press to enable the Hardwired Siren, or
Press to disable the Hardwired Siren.
AUTO REPORT
The associated detectors will emit a radio signal to the Control Panel every one
hour as an aknowledgement of proper operation. If within a certain period of
time, the control panel does not receive a radio signal from the detectors. This
feature, if enabled, allows the Control Panel to show an abnormal indication as a
reminder.
Default setting: ON 12H
Scroll through the menu until ‘2-4 Auto Report Func.’ is displayed. The current
setting will also be displayed.
CODE LEARNING
This enables the Control Panel to be learned the ID from each detector.
Scroll through the menu until ‘Learning ID’ is displayed and press .
Pressing tamper switch on the detector will emit ID code to the Control Panel
instantly.
Three possibilities would happen as follows:
Learning OK – the ID code was learned by the Control Panel successfully.
Time Out – the time involved for learning the ID code is 60s. During this
duration, fail to press the tamper switch on the detector would result in overdue
programming.
ID Duplicate – the same ID code was learned by the Control Panel beforehand.
Try again for code learning.
NAME
Default setting: ‘No name’
Scroll through the menu until ‘:2 Zone Name’ is displayed. The current setting
will also be displayed.
To change the setting press .
Scroll through available options until the required setting is displayed.
Press to save and exit, or
Press to exit without saving.
TYPE
Each alarm zone may be programmed to operate in one of 5 different modes
depending on the type of alarm function it is required to perform. The following
alarm types are available:
Intruder
- provides standard intruder monitoring with normal ARM and PARTIAL ARM
functions.
24 Hour Intruder
- used to provide 24 hour monitoring of areas requiring continuous security
protection even while the system is Disarmed, (e.g. gun lockers). Activation of
any detector on a security zone will immediately initiate a Full Alarm condition.
Fire
- used to provide 24 hour monitoring of any Fire/Smoke detectors fitted to the
system. Activation of any detector will immediately initiate a Full Alarm
condition.
ENEN
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elro HA68 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elro HA68 in the language / languages: English as an attachment in your email.

The manual is 3,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elro HA68

Elro HA68 Quick start guide - English - 1 pages

Elro HA68 Quick start guide - German - 1 pages

Elro HA68 User Manual - German - 34 pages

Elro HA68 Quick start guide - Dutch - 1 pages

Elro HA68 User Manual - Dutch - 34 pages

Elro HA68 Quick start guide - French - 1 pages

Elro HA68 User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info