708667

Elro AP5500 - Pro Alarm System Manual

48
Zoom out
Zoom in
Previous page
1/49
Next page
DIGITAL DIALER TRANSMISSION
PROTOCOL
Contact ID Event Codes
46
LED on Magnetic Contact Detector illuminating
when door or window is opened.
1. Low battery – replace batteries.
Definition
Code
Fire/Smoke Alarm
110
Panic Alarm
120
Intruder Alarm
130
24hr Intruder
133
System Tamper
137
AC Failure
301
System Low Battery
302
Sensor Tamper
383
Sensor Low Battery
384
Cancel/Abort Alarm
406
System Test
601
Open/Close by User
401
PIR Detector LED flashes on detection of
movement, (device in normal operation mode)
1. Low battery – replace battery.
Full alarm condition occurs when system has
not been triggered by an intruder or is disarmed
1.
Tamper switch activation
-
check all detector battery covers to ensure
correctly fitted
-
check Control Panel and Siren are securely
mounted to the wall and tamper switch is
closed
2.
Panic alarm operated from a Remote Control or
Keypad
3.
Jamming detection circuit operated
LED on remote control not illuminating, or is
dim when unit is operated
1.
Ensure battery is connected with correct polarity
2.
Ensure battery connections are good
3.
Replace battery
PIR Detector false alarming
1.
Ensure that the detector is not pointing at a
source of heat or a moving object
2.
Ensure that the detector is not mounted above a
radiator or heater
3.
Ensure that the detector is not facing a window
or in direct sunlight
4.
Ensure that the detector is not in a draughty
area
5.
Sensitivity detection set too high –reset to low
sensitivity detection
PIR Detector not detecting a person’s movement
1.
Check battery connections are good.
2.
Sensitivity detection set too low– reset to high
sensitivity detection.
3.
Check that the detector is correctly set up.
4.
Ensure DIP switches 1-4 of SW3 are correctly
set.
5.
Ensure that detector is mounted the correct way
up.
(i.e. with detection window at the bottom)
6.
Ensure that the detector is mounted at the
correct height, (i.e. 2-2.5m).
7.
Allow up to three minutes for detector to
stabilize.
Magnetic Contact Detector not working
1.
Ensure batteries are connected with correct
polarity.
2.
Ensure battery connections are good.
3.
Ensure ‘House Code’ is correctly set.
4.
Ensure DIP switches 9, 10 and 11 are set
correctly.
5.
If no external contacts are connected ensure
jumper link fitted.
6.
If external contacts are connected
a.
Ensure jumper link removed
b.
Check that all contacts are closed.
c.
Check all contacts are wired in series.
Magnetic Contact Detector false alarming
1.
Ensure that gap between magnet and detector
is less than 10mm.
2.
Tamper switch below battery cover not
depressed – check battery cover is fitted
correctly and that fixing lugs are not broken.
… 48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elro AP5500 - Pro Alarm System at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elro AP5500 - Pro Alarm System in the language / languages: English as an attachment in your email.

The manual is 3,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elro AP5500 - Pro Alarm System

Elro AP5500 - Pro Alarm System Quick start guide - English - 8 pages

Elro AP5500 - Pro Alarm System Quick start guide - German - 10 pages

Elro AP5500 - Pro Alarm System Quick start guide - Dutch - 8 pages

Elro AP5500 - Pro Alarm System User Manual - Dutch - 42 pages

Elro AP5500 - Pro Alarm System Quick start guide - French - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info