708656

Elro AG40MA Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
INTRODUCTION
The door/window sensor AG40MA11 is designed for use with the Home Alarm System AG400011.
The Magnec sensor consists of two parts; a detector (a) and a magnet (b). Designed to be fied to doors or
windows with the magnet mounted on the moving/opening part, and can then detect when the door or
window is opened.
INSERTING BATTERIES
Unscrew the screw (c) at the boom of the sensor to remove the rear cover (d), and place the 3 included 1.5V
AAA baeries in the baery compartment. Ensure you are not pressing the tamper switch (e) on the boom of
the sensor. Then remove or bring the magnet to the detector, the LED (f) of the detector lights up.
LINKING TO THE HOME ALARM SYSTEM AG400011
Before mounng the sensor, you must first link the sensor to the alarm panel. When adding a sensor to the
alarm system, it can be added under five different security types that differ based on in which mode they can
give an alert and whether or not there is a delay. The types are:
- Security Type “0”: Fully Armed: The sensor will be acvated only when the system is in Full Arm mode. This
sensor will not be acvated in Paral Arm mode. When the sensor is triggered, the alarm will sound
immediately without any preset delay.
- Security Type “1”: Parally Armed and Fully Armed: The sensor will be acvated when the system is either
fully or parally armed. When the sensor is triggered the alarm will sound immediately without any preset
delay.
- Security Type “2”: Fully Armed + Delay: Same as Security Type “0”, except when the sensor is triggered the
alarm will sound aer a preset Entry delay. This is mostly used for the main entrance to prevent any
accidental triggering of the alarm by the user.
- Security Type “3”: Paral Arm and Fully Arm + Delay: Same as Security Type “1” except when the sensor is
triggered the alarm will sound aer a preset Entry delay. This is mostly used for the main entrance to
prevent any accidental triggering of the alarm by the user.
- Security Type “4”: 24Hrs intruder: The sensor will immediately trigger an alarm, regardless whether the
system is (parally) armed or disarmed. This is normally used to protect areas from any unauthorized access,
such as a safe box or an electrical maintenance room, etc.
When you have selected which security type fits best with the sensor you are using, follow these steps to link
the sensor to the alarm system:
1. Ensure you have inserted the baeries so that the sensor is powered on
2. On the alarm panel, enter your PIN + DISARM key to disarm the system.
3. Then enter your PIN + 15 + (Security Type) + PARM to start the binding process.
The DISARM LED will start to blink for 30 seconds with a beep tone.
4. Within 30 seconds, set the sensor to enter binding mode by pressing the tamper key on the back for a few
seconds and releasing.
5. If the sensor has been successfully linked to the alarm panel, the DISARM LED will turn on for 1 second
and you will hear a long beep. A keypad LED will turn on to indicate the zone number that has been assigned
to the sensor (Numbers 1-9 for zones 1-9, 0 for sensor zone 10 or higher). We advise you to note down the
locaon and the zone number.
6. If binding fails, it will meout aer 30 seconds and 3 short beeps will be heard.
7. To exit the binding process, press the DISARM key.
TESTING
Decide which doors/windows are to be protected by fing magnec contact sensors, (usually the front and
back doors). Addional sensors may also be fied where required to other vulnerable doors or windows, (e.g.
garage, pao doors etc.).
Before mounng, it is wise to first test the contact where you want to mount it, to ensure it is within range of
the control panel. To test enable test mode on the alarm panel by entering your PIN + 03 + PARM key.
Next press and release the tamper switch on the back of the sensor when you are holding it near the place
where you want to mount it, you should now hear a chime from the alarmpanel. When you have finished the
test, press the DISARM key to exit test mode.
-1- -2-
1 2
ON
AAA - 1,5V
AAA - 1,5V
Tamper
switch
55mm
32mm
(a)
(b)
(c)
(f)
(d)
(e) (e)
Alternave
mounng
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elro AG40MA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elro AG40MA in the language / languages: English as an attachment in your email.

The manual is 2,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elro AG40MA

Elro AG40MA User Manual - German - 2 pages

Elro AG40MA User Manual - Dutch - 2 pages

Elro AG40MA User Manual - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info