Manual Elma DT5500A (page 26 of 28) (English, Danish, Swedish, Norwegian)

668435

Zoom out

Zoom in

1/28

Elma DT5500A

side 26

d)Being free from the “TEST” button or pushing down the “TEST” button in the “LOCK “

status can exit from the “LOCK” status and shutoff the high-voltage，synchronously, the

resistance values is indicated in the primary display will be held, and the secondary display

still be in the status of monitoring the insulation voltage for the tested.

e)Subsequently, discharge the balance insulation voltage of the tested through the inner

switch of the meter. Turning the function switch can exit automatically from testing status

during the process。

Low resistance (continuity) measurements

a). Set the range switch to 400Ω/BZ Position

b). Connect the red test lead to the V Ω terminal and black to the COM terminal.

c). Connect the tips of the test leads to both ends of the circuit under test. read resistance

in Ω on the LCD. The two ranges(40.00/400.0Ω) can be switched automatically; the

primary display of the resistance in Ω, flashes in synchronous with the analog bar.

d). When the impedance on circuit is below approximately ≤35Ω.It will indicate by a

continuous beeper.

e) The current is from 200 to 220mA while the tested resistance is 0Ω

f) The high voltage symbol “ “ flashes along with a primary display of “>30V” and the

buzzer warns frequently if the voltage (AC/DC) is more than 30V.

AC/DC Voltage measurements

a). Set the range switch to ACV or DCV position

b). Connect red test lead to “V Ω” terminal and black test lead to terminal “COM”.

c). Connect test prods of test leads IN PARALLEL to the circuit being measured.

d). Read the voltage value on LCD.

Power tools and small appliances

This test would also apply to other similar equipment that has a line cord. For double

insulated power tools, the megohmmeter lead shown connected to the housing would be

connected to some metal part lf the tool(e..g chuck,blade).

Note:The switch of the device must be in the “ON”position and the main power should be

disconnected.

Motors

AC-Disconnect the motor from the line by disconnecting the wires at the motor terminals

or by opening the main switch. If the main switch is used and the motor also has a starter

then the starter must be held, by some means, in the “ON” position. In the latter case, the

measured resistance will include the resistance of the motor, wire and all other

components between the motor and the main switch. If a weakness is in dicated, the motor

and other components should be checked individually. If the motor is disconnected at the

motor terminals, connect one megohmmeter lead to the grounded motor housing and the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elma DT5500A in the language / languages: English, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 1,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elma DT5500A Manual

Product: