741424
1
Zoom out
Zoom in
Previous page
1/16
Next page
1/16
JP1
JP3
JP2
1
2
3
+IN -IN SH -OUT +OUT PC
CC
H1
JP4
- +
DESCRIZIONE GENERALE
Il modulo di uscita IO501 con microprocessore ed isolatore di corto circuito è un modulo attuatore (MU) con
uscita a contatti puliti da utilizzarsi con centrali di rivelazione incendio ELKRON della serie FAP.
Il modulo non necessita di alcuna alimentazione esterna ma è alimentato direttamente dalla linea
rivelazione. Un ponticello presente sul modulo consente di selezionare il contatto di uscita se normalmente
aperto oppure chiuso. Il modulo dispone di un ingresso per la supervisione della tensione di alimentazione
locale (24Vcc) dell’apparecchiatura da pilotare: una mancanza di tale tensione o la sua non voluta presenza
è segnalata dal modulo in centrale. Il LED bicolore, in condizioni operative, indica lo stato del modulo
mentre, in modali service, può essere utilizzato per visualizzare l’indirizzo del modulo tramite una funzione
specifica attivata dalla centrale. Sempre da centrale è possibile programmare il ritardo fra la ricezione del
comando di attivazione relè e l'effettivo pilotaggio del re(ritardo hold-off). Questo ritardo è espresso in
secondi e può coprire un range fra 0-255 in step da 1 secondi. Il valore di fabbrica del ritardo è pari a 0.
Per ulteriori informazioni fare riferimento al manuale programmazione delle centrali ELKRON serie FAP.
INDIRIZZAMENTO
L'indirizzo (1-128) è impostato via software e memorizzato su una memoria non volatile. Il modulo può
essere indirizzato dalla centrale in modalità automatica o manuale. Per ulteriori dettagli vedere il
manuale di programmazione della centrale.
MORSETTIERA
Nr.
Descrizione
+IN
Ingresso positivo linea rivelazione
-IN
Ingresso negativo linea rivelazione
SH
Schermo linea rivelazione
-OUT
Uscita negativo linea rivelazione
+OUT
Uscita positivo linea rivelazione
PC
Contatto NA/NC
CC
Contatto C
JP1: Chiuso: impostazione di default
Aperto: toglie alimentazione al modulo.
JP2: Chiuso: cortocircuita i positivi della linea rilevazione.
Aperto: impostazione di default
JP3: Posizione 1-2: contatto di uscita normalmente aperto (NA).
Impostazione di default
Posizione 2-3: contatto di uscita normalmente chiuso (NC).
JP4: Connettore per supervisione 24Vcc locale. Utilizzare il cavo in dotazione.
Cavo rosso: ingresso positivo 24Vcc
Cavo nero: ingresso negativo 24Vcc
É possibile definire in centrale la segnalazione di guasto a fronte della mancanza oppure della presenza
della tensione locale.
IO501
Modulo di uscita - Output module - Módulo de salida
DS80SC2N-001B
LBT80768
ITALIANO
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron IO501 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron IO501 in the language / languages: English, Italian, Spanish as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info