741475
1
Zoom out
Zoom in
Previous page
1/3
Next page
HPA100A
SIRENA DA INTERNO AUTOALIMENTATA
INTERNAL SELF-POWERED SOUNDER
1-a
1-b
ITALIANO
CARATTERISTICHE GENERALI
La sirena da interno autoalimentata HPA100A è dotata di:
Due modalità di suonata differenziate
Predisposizione per batteria di tampone 9V alcalina o ricaricabile Ni-Mh
Controlli gestiti mediante microprocessore
Comandi di blocco con contatto NC programmabili riferiti a Positivo – Negativo
Time-out di blocco suonata a fronte di taglio cavo (4 programmazioni)
Protezione anti-apertura
Le sirene serie HPA100A dispongono di due diverse segnalazioni legate ai comandi BL1 e BL2, entrambi di tipo NC con riferimento
programmabile al Positivo o Negativo.
Il comando BL1 (f= 3500 – 3700 Hz modulati) è relativo al segnale di allarme di potenza ed è subordinato al time-out programmabile.
Il comando BL2 (f= 3050 Hz impulsata) può essere utilizzato per segnalazioni quali pre-allarme, guasto, gong, etc. Per utilizzare questo
comando è necessario aprire il ponticello JP3. Inoltre sono disponibili due livelli acustici differenti (alto – basso), selezionabili tramite il
ponticello JP4 (vedi “
CONFIGURAZIONI
”).
1 INSTALLAZIONE
a) Rimuovere i tappi di copertura e svitare le viti.
b) Utilizzare una delle
predisposizioni “A”
per il passaggio cavi evidenziate in “fig.1-b” sfondando la parete. Se necessario rimuovere la scheda
elettronica agendo sui due
gancetti “B”
. Sono anche disponibili delle predisposizioni per ingresso cavi da canalina sui lati del contenitore.
c) Fissare il fondo della sirena utilizzando
i fori “C”
in caso di fissaggio a parete o
i fori “D”
in caso di fissaggio su scatola da incasso.
d) Collegare la sirena alla centrale e configurare i ponticelli secondo le necessità.
e) Richiudere il coperchio della sirena.
2 CONNESSIONI
BL2 INGRESSO DI COMANDO BL2 - SEGNALAZIONE
BL1 INGRESSO DI COMANDO BL1 - ALLARME
+ POSITIVO DI ALIMENTAZIONE
- NEGATIVO DI ALIMENTAZIONE
TAMPER CONTATTO ANTI-APERTURA
3 CONFIGURAZIONE
Le configurazioni della sirena si effettuano tramite ponticelli dotati di cavallotto. Di seguito vengono elencate le funzioni dei ponticelli (in
Grassetto
le programmazioni di fabbrica).
POSIZIONE FUNZIONE
CHIUSO
APERTO
JP1 Riferimento ingressi
A positivo
A negativo
JP3 Ingresso BL2
Disabilitato
Abilitato
JP4 Livello sonoro BL2
Livello Basso
Livello Alto
JP5 Chiuso – JP6 Chiuso = No Time-out
JP5 Aperto – JP6 Chiuso = 3 min.
JP5 Chiuso – JP6 Aperto = 6 min.
JP5 – JP6 Time-out blocco suonata
JP5 Aperto – JP6 Aperto = 9 min.
POSIZIONE FUNZIONE
POSIZIONE “A”
POSIZIONE “B”
JP2
Carica batterie
*
Disabilitato- Batterie Alcaline
Abilitato- Batterie Ni-Mh
Tipo batteria 6LR61 Alcalina
6LR61 NiMh
* = Abilitare il carica batterie solo in presenza di batteria al Ni-Mh.
Non usare assolutamente con batterie alcaline.
4 ESEMPIO DI COLLEGAMENTO
( NORMALMENTE
ECCITATO )
+
-
TAMPER
BL1
BL2
HPA100A
CENTRALE
LINEA 24H
RELE' DI
ALLARME
C NO NC + SIR -
ALTRI DISPOSITIVI
USCITA EL.
COMANDO OPZIONALE
PER MODALITA' DI SUONATA INTERMITTENTE
ATTENZIONE: APRIRE IL PONTICELLO JP3
CARATTERISTICHE TECNICHE
Tensione nominale di alimentazione .......................12V
Tensione di funzionamento .....................................10.5V ÷ 15V
Assorbimento max in allarme ..................................260mA
Assorbimento max. a riposo ....................................12mA
Frequenza (suonata di allarme)...............................3500 – 3700 Hz
Pressione acustica in allarme..................................110 dB(A) @ 1m
Frequenza (modalità segnalazione) ........................3050 Hz
Pressione acustica in segnalazione ........................72 / 102 dB(A) @ 1m in funzione di JP4
Microswitch antiapertura..........................................1A @ 24V
Temperatura di funzionamento................................-10°C + 55°C
Grado di protezione involucro..................................IP41
Dimensioni (L x H x P).............................................145 x 100 x 42 mm
ENGLISH
GENERAL FEATURES
The self-powered internal sounder HPA100A is equipped with
Dual mode sound management
It is possible to house a backup battery (9V alkaline or Ni-Mh rechargeable)
Controls managed through microprocessor
Chance of programming block inputs referred to positive or negative
Sound time-out in case of permanent lack of block signal (4 different programmable timings)
Protection against opening
HPA100A sounders family could generate two different sounds in function of BL1 and BL2 command inputs, normallly closed type and
with programmable reference to Positive or Negative.
BL1 command (f= 3500 – 3700 Hz modulated) is related to the alarm function (high power sound) and it is controlled by the
programmable time-out.
BL2 command (f= 3050 Hz pulsed) could be utilized for additional signalling like pre-alarm, fault, gong, and so on. To enable this input is
necessary to open the JP3 jumper. There are two different sound levels (High – Low) selecvtable by means of JP4 jumper (see
“CONFIGURATIONS”
paragraph).
1 INSTALLATION
a) Remove the screw caps and release the screws.
b) Utilize one of the planned cable entry holes “A”. If necessary release the electronic board from the ledge “B” and remove it. There are
other pre-fractured holes on three side of the box for cable trunking / rigid pipe.
c) Fix the bottom of the siren utilizing “C” holes in case of wall mounting, or “D” holes in case of 3 modules box.
d) Lay the sounder to the control panel and configure the jumper
e) Close the sounder cover.
2 CONNECTIONS
BL2
BL2 COMMAND INPUT - SIGNALLING
BL1
BL1 COMMAND INPUT - ALARM
+ POWER SUPPLY: POSITIVE POLE
- POWER SUPPLY: NEGATIVE POLE
TAMPER TAMPER CONTACT
3 CONFIGURATION
The siren is configured by means of jumpers. The jumpers functions are listed (factory programming in
block letters
):
POSITION FUNCTION CLOSED OPEN
JP1 Input references
To positive
To negative
JP3 Input BL2
Not used
Enabled
JP4 BL2 Sound level
Low level
High level
JP5 Closed – JP6 Closed = No Time-out
JP5 Open – JP6 Closed = 3 min.
JP5 Closed – JP6 Open = 6 min.
JP5 – JP6 Time-out ringing lock
JP5 Open – JP6 Open = 9 min.
POSITION FUNCTION
POSITION “A”
POSITION “B”
JP2
Battery Charger
*
Disabled- Alkaline Battery
Enabled - Ni-Mh Battery
Battery Type 6LR61 Alkaline
6LR61 NiMh
* = Enable the battery charger only if Ni-Mh rechargeable battery is utilized
Absolutely NOT USE in case of alkaline battery
4 CONNECTIONS DIAGRAM
TAMPER
( NORMALLY
POWERED )
+
-
BL2
BL1
C NO NC + SIR -
24H LINE
ALARM
RELAY
ELECTRICAL
OUTPUT
CONTROL PANEL
OTHER DEVICES
HPA100A
OPTIONAL COMMAND FOR
SIGNALLING SOUND
WARNING: OPEN JP3
TECHNICAL FEATURES
Rated supply voltage .............................................. 12V
Operating voltage.................................................... 10.5V ÷ 15V
Max current in alarm ............................................... 260mA
Max standby current................................................ 12mA
Working frequency (alarm function) ........................ 3500 – 3700 Hz
Acoustic pressure (alarm function).......................... 110 dB(A) @ 1m
Working frequency (signalling function) .................. 3050 Hz
Acoustic pressure (signalling function).................... 72 - 102 dB(A) @ 1m (depending from JP4)
Anti-opening/anti-removal micro-switch .................. 1A @ 24V
Working temperature............................................... -10°C + 55°C
Case protection degree........................................... IP41
Dimensions (w x h x d)............................................ 145 x 100 x 42 mm
2 3
Tappi copertura / Screw caps
JP4
JP6
JP5
JP3
JP1
COM1
JP2
A
BATT
B
BATTERY
DS80HP94-001
A
LBT80645
ELKRON
Tel. +39(0)11.3986711 – FAX +39(0)11.3986703
www.elkron.com
- mail to: info@elkron.it
ELKRON è un marchio commerciale di URMET S.p.A.
Via Bologna, 188/C - 10154 Torino (TO) – Italy
www.urmet.com
Made in P.R.C.
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron HPA100A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron HPA100A in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info