741423

Elkron DS80PS42 Manual

1
Zoom out
Zoom in
Previous page
1/2
Next page
ALIMENTATORE PS515
PS515 POWER SUPPLY
ALIMENTATEUR PS515
ITALIANO
DESCRIZIONE GENERALE
L’alimentatore PS515 è costruito in riferimento alla norma EN 50131-6.
L’impostazione di fabbrica della tensione di uscita (14,4V⎓) tiene conto
della caduta di tensione di 0,6 / 0,7V ai capi del diodo di protezione
presente in molte centrali di allarme e nella quasi totalità delle centrali
Elkron.
Alimentatore in CAT II 2500 V. L’alimentatore che, una volta installato, è
soggetto a tensioni transitorie superiori a quelle della categoria di
sovratensione di progetto, necessita di una protezione supplementare
delle tensioni transitorie esterne all’apparecchiatura.
CARATTERISTICHE TECNICHE
Tensione d’ingresso ....................................... 220-240V~ ; 50/60Hz ; 0,6A
Tensione di uscita ........................................... 14,4V⎓
Corrente max erogabile ................................... 1,5A
Ripple max ...................................................... 300mVpp
Fusibile ........................................................... T2AL – 250V~
I cavi impiegati devono rispondere alla norma IEC 60332-1-2 se di
sezione 0,5 mm² o superiore, oppure alla norma IEC 60332-2-2 se di
sezione inferiore a 0,5 mm².
NOTA: Il morsetto “C” (test), se forzato a 0V (massa) porta la tensione di
uscita a 11V⎓ circa per consentire il controllo batteria (per le centrali di
allarme predisposte o che prevedono la gestione di questa funzione).
LEGENDA SIMBOLI
Simbolo
Spiegazione
Tensione di alimentazione continua
~
Tensione di alimentazione alternata
Alimentatore dotato di un doppio isolamento
Riferirsi al manuale d’installazione del dispositivo
ELKRON
Tel. +39 011.3986711 - Fax +39 011.3986703
www.elkron.com – mail to: info@elkron.it
ENGLISH
FRANCAIS
GENERAL INFORMATION
The PS515 power supply is manufactured with reference to the EN50131-6
standard.
The output voltage set to 14,4V⎓ considers the voltage drop (0,6 / 0,7V)
across the protection diode usually mounted on the alarm control panels,
and in particular on the Elkron control panels.
Power supply in CAT II 2500 V. Once installed, the power supply is subject
to transient voltages higher than those of the overvoltage category for
which is was designed. For this reason, an additional transient voltage
protection is required outside the device.
TECHNICAL CHARACTERISTICS
Input Voltage ................................................. 220-240V~ ; 50/60Hz ; 0,6A
Output Voltage ................................................. 14,4V⎓
Max Output Current ......................................... 1,5A
Max Ripple ....................................................... 300mVpp
Fuse ................................................................ T2AL – 250V~
Wires with cross-section area of 0.5 mm² or larger must comply with
IEC 60332-1-2; wires with cross-section area smaller than 0.5 mm² must
comply with IEC 60332-2-2.
NOTE:
When connected to 0V (ground), the “C” terminal brings the output voltage
to roughly 11V⎓ in order to allow the battery test (for the alarm control
panels providing this function).
KEY TO SYMBOLS
Symbol
Description
Direct input voltage
~
Alternating input voltage
Power supply fitted with double insulator
See the installation manual of the device
DESCRIPTION GÉNÉRALE
L’alimentation PS515 est construite en référence à la norme EN50131-6.
Le réglage d’usine de la tension de sortie (14,4V⎓) tient compte de la
chute de tension de 0,6 / 0,7 V aux extrémités de la diode de protection
présente dans de nombreuses centrales d’alarmes et dans la presque
totalité des centrales Elkron.
Alimentation en CAT II 2500 V. L’alimentateur, qui une fois installé peut
subir des tensions transitoires supérieures à celles de la catégorie de
surtension de projet, nécessite une protection supplémentaire des
tensions transitoires externes à l’équipement.
CARACTÉRISTIQUES TECHNIQUES
Tension d’entrée ............................................ 220-240V~ ; 50/60Hz ; 0,6A
Tension de sortie ............................................ 14,4V⎓
Courant max. fourni......................................... 1,5A
Ondulation max. .............................................. 300mVpp
Fusible ............................................................ T2AL – 250V~
Les câbles utilisés doivent satisfaire la norme IEC 60332-1-2 si la
section mesure au moins 0,5 mm², ou la norme IEC 60332-2-2 si la
section mesure moins de 0,5 mm².
REMARQUE :
La borne « C » (test), si forcée à 0 V (masse) porte la tension de sortie à
11 V⎓ environ, afin de permettre le contrôle de la batterie (pour les
centrales d’alarmes prévues ou qui prévoient la gestion de cette fonction).
LÉGENDES SYMBOLES
Symbole
Explication
Tension d’alimentation continue
~
Tension d’alimentation alternée
Alimentation à double isolement
Se reporter au manuel d’installation du dispositif
DS80PS42-001B LBT80110
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron DS80PS42 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron DS80PS42 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info