741433

Elkron DK500M-P Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
DK500M-P
DK500M-P/B
Proximity reader
Lector de proximidad
3
4
5
6
ELKRON
TEL. +39.011.3986711 – FAX +39.011.3986703
www.elkron.com – mail to: info@elkron.it
ELKRON is a trademark of URMET S.p.A.
ELKRON es una marca registrada de URMET S.p.A
Via Bologna, 188/C - 10154 Torino (TO) – Italy
www.urmet.com
MADE IN ITALY
ENGLISH
WARNING: This document provides only some
essential product information.
Refer to the MP500 control panel manuals for more detailed
information.
GENERAL DESCRIPTION
DK500M-P is a connecting device set for use with DK30 keys.
It comes in the following colours:
DK500M-P: black front
DK500M-P/B: white front
The following adapters are available for domestic series:
DKA/A - (KT2500111) 5 pieces for AVE® Sistema 45
DKA/G - (KT2400111) 5 pieces for Gewiss® Playbus
DKA/I - (KT2200111) 5 pieces for B-ticino® Light and International
DKA/L - (KT2300111) 5 pieces for B-ticino® Living
For the use of readers in the series Vimar® Idea and Vimar®
8000 you must use the adapters available on the market:
Art. 16544 for Vimar® Idea and Art. 08324 for Vimar® 8000.
POSITIONING
WARNING: In accordance with EN50131 standards, the
proximity readers installed outside the protected zone must be
protected by devices to prevent tampering. EN50131
certification cannot be achieved if these devices are missing.
The proximity reader must be placed in an enclosed space far
from water and moisture sources.
Can be placed more readers side by side only if they have
sequential address (reader n.1, reader n. 2, …).
CABLING
The proximity reader is connected to the bus MP500 control
panel. The overall length of all the bus sections must not
exceed 400 m.
CONNECTING THE INPUTS
Connect the anti-tamper device to input 1 of the reader (yellow
wire: interrupt the wire by cutting it and connect the two pieces
to the anti-tamper device. The TAMPER is the factory setting.
WARNING
:
“Double balance” is the only EN50131
compliant connection mode. Refer to the manuals of MP500
units for further, more detailed information.
ACQUISITION
The reader can be acquired by pressing the dedicate button
(Fig.5) following the instructions inside the control panel
installation manual. To display the reader address, press the
button and count the blink of the lateral yellow LED.
FRONT VIEW
The device features four green LEDs (A-B-C-D) used to indicate
the status of the controller sectors, plus one red LED (E) used
to indicate system information and reading key.
“F” corresponds to the key proximity detector.
USE
Total Arming and disarming
Hold the Key to approximately 1 cm from the sensor F and
leave when the red LED E blinks. The 4 green LED (A-B-C-D)
indicate the status of the controlled sectors: LED ON indicate an
armed sector. If a LED is associated to more sectors, when
they are not all armed the LED blinks. The possibility of
activation of each sector depends on the programming of the
reader and the key used.
Partial arming
Hold the Key to approximately 1 cm from the sensor F, keep it
for at least 3 seconds and leave when the 4 green LED blink.
After a while the reader shows the possible combinations of
partialisation starting with the last made.
To confirm the choice hold the Key. The LEDs indicate the
armed sectors.
NOTE: If you use a key is not acquired (key not recognized),
the 4 green LED will blink rapidly.
TECHNICAL CHARACTERISTICS
Rated supply voltage ............................................. 13,8 Vdc
(picked by the control panel through the bus)
Operating voltage min/max ................................... 9 Vdc ÷ 15 Vdc
Rated current absorption at 12 Vdc:
LEDs OFF .............................................................. 40 mA
All LEDs ON .......................................................... 68 mA
ESPANOL
ATENCIÓN: En este documento solo se citan algunas
indicaciones esenciales del producto.
Para más información detallada, remitirse a los manuales
de las centrales MP500.
DESCRIPCIÓN GENERAL
El DK500M-P es un dispositivo de conexión preparado para el
uso de llaves DK30. Disponible en los sig. colores:
DK500M-P: parte frontal negra
DK500M-P/B: parte frontal blanca
Se encuentran disponibles los siguientes adaptadores para las
series civiles:
DKA/A - (KT2500111) 5 piezas para AVE® Sistema 45
DKA/G - (KT2400111) 5 piezas para Gewiss® Playbus
DKA/I - (KT2200111) 5 piezas para B-ticino® Light e International
DKA/L - (KT2300111) 5 piezas para B-ticino® Living
Para usar los lectores en las series Vimar® Idea y Vimar® 8000,
se deben utilizar los adaptadores existentes en el mercado:
Art. 16544 para Vimar® Idea y Art. 08324 para Vimar® 8000.
POSICIONAMIENTO
ATENCIÓN: De acuerdo con las normas EN50131, los
lectores montados en el exterior de la zona protegida se deben
proteger mediante dispositivos antisabotaje (tamper); la falta de
los mismos provoca la pérdida de la certificación EN50131.
El lector de proximidad debe estar ubicado en un ambiente
resguardado y protegido del agua y la humedad.
Se pueden combinar varios lectores, siempre que cuenten con
número de dirección secuencial (lector n.1, lector n. 2, …).
CABLEADO
El lector de proximidad se debe conectar en el bus de la central
MP500. La longitud global de todos los tramos del bus no debe
superar los 400 metros.
CONEXIÓN ENTRADAS
Conectar el tamper a la entrada 1 del lector (cable amarillo:
interrumpir el cable, cortándolo y conectar los dos fragmentos
al tamper). La entrada viene de fábrica ya programada como
SABOTAJE.
ATENCIÓN
:
El único modo de conexión de conformidad
con la norma EN50131 es la de “Doble Balanceado”. Para más
información detallada consultar los manuales de las centralitas
MP500.
ADQUISICIÓN
Adquirir el lector presionando el botón correspondiente
(Fig.5)
siguiendo las instrucciones presentes en el manual de instalación
de la central. Para visualizar el número del lector, presionar el
botón y contar el número de parpadeos del LED amarillo lateral.
VISTA FRONTAL
El dispositivo presenta 4 LED de color verde (A-B-C-D), utilizados
para indicar el estado de los sectores controlados, y 1 LED de
color rojo (E) para indicar señalizaciones del sistema y llave
presente. “F” corresponde al sensor de proximidad de la llave.
USO
Activación y desactivación total
Acercar la llave a aproximadamente 1 cm del sensor F y alejarla
cuando el LED rojo E parpadea. Los 4 LED de color verde (A-B-C-D)
indican el estado de los sensores controlados: LED encendido
corresponde a sector activado. Si a un LED se asocian varios
sectores, cuando no están todos activados, el LED parpadea. La
posibilidad de activación de cada sector depende de la programación
del lector y de la llave utilizada.
Activación parcial
Acercar la llave a aproximadamente 1 cm del sensor
F
, mantenerla
durante al menos 3 segundos y alejarla cuando los 4 LED verdes
parpadean
.
Después de algunos instantes, el lector presenta las
posibles combinaciones de parcialización iniciando por la última
realizada. Para confirmar la elección, acercar la llave: se encienden los
LED de los sectores activados.
NOTA:
Si se usa una llave no adquirida (llave no reconocida),
parpadean rápidamente los 4 LED verdes.
CARACTERÍSTICAS TÉCNICAS
Tensión nominal de alimentación ......................... 13,8 Vcc
(tomados de la central mediante bus)
Tensión de funcionamiento mín./máx. .................. 9 Vcc ÷ 15 Vcc
Corriente nominal absorbida a 12 Vcc:
LED apagados ...................................................... 40 mA
LED encendidos (todos) ....................................... 68 mA
DS80DK52
-001C LBT80087
LECTOR
LECTOR
LECTOR
NC
MONO
BALANCEADO
DOBLE
BALANCEADO
READER
READER
READER
NC
SINGLE
BALACING
DOUBLE
BALACING
EN50131
EN50131
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron DK500M-P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron DK500M-P in the language / languages: English, French, Italian, Spanish as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info