741418
3
Zoom out
Zoom in
Previous page
1/8
Next page
ENGLISH
DC600S - DC600S/BR
WHITE OR BROWN MINI MAGNETIC CONTACT WITH SHOCK DETECTOR
1. LED Indicator/Learning/Test Button
2. Cover fixing screw
3. Wall-mounting hole arrangement
4. Tamper switch
5. Battery insulation
6. Jumper for selecting detection type (JP3)
7. Jumper for selecting detection sensitivity (JP4, JP5)
8. Jumper for selecting magnet use mode (JP1)
9. Battery
10. Magnet
11. Magnet fixing screw hole
12. Magnet spacer
Jumper. Default position
LED indicator
In normal operating mode, the LED is off, except for the following situations:
When the tamper switch of the device is opened
When the battery of the device is flat
When the device is in Test mode
The LED does not flash if the tamper switch and the battery of the device are working normally and not in Test mode.
The LED flashes to indicate that a signal is being transmitted and flashes rapidly twice when it receives a recognition signal from
the control unit.
Jumper
Management of alarms generated by opening of the magnet
The detection of the alarm generated by the opening of the magnet can be enabled or disabled by jumper JP1:
If the jumper is ON (the jumper is inserted on the two pins), detection is deactivated and the shock/vibration alarm
remain enabled.
If the jumper is OFF (jumper removed or "arranged" on a pin), detection is enabled (default setting).
Important note: insert the jumper on JP1 in case you are using the device as shock detector only.
Management of alarms generated by shocks/vibrations
The detection of the alarm generated by impulses caused by shocks or vibrations can be configured as follows.
Single pulse detection
The alarm is generated by the detection of a single pulse exceeding the set threshold.
Multiple pulse/sum of vibrations detection
The alarm is generated by the detection of at least one of the following two conditions:
I. When 3 pulses are detected in a time interval of less than 20 seconds.
II. When the accumulation of vibrations detected in a time interval of less than 2 minutes exceeds the set threshold.
The modes described are determined by jumper JP3:
If the jumper is ON (the jumper is inserted on the two pins): Single pulse detection (default setting)
If the jumper is OFF (jumper removed or "arranged" on a pin): Multiple pulse/sum of vibrations detection
QUICK GUIDE
DS80MM1L-002
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron DC600S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron DC600S in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elkron DC600S

Elkron DC600S User Manual - English, German, French, Italian - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info