128190
11
Zoom out
Zoom in
Previous page
1/12
Next page
Operation 
Model with electronic controls
A- Lighting, on/off.
B - Fan off (Stand by)
C - Timer for selected speed (visualizes the speed
selected and flashing LED on the lower side of the
display).
This knob permits the operation of the cooker hood
for a established period:
20 minutes if the speed selected is 1
15 minutes if the speed selected is 2
10 minutes if the speed selected is 3
5 minutes if the intensive speed P is selected.
D - Display showing:
Fan speed (1-3-P).
Change grease filters (grease filter saturation
indicator - F)
After washing the anti-grease filter, depress
knob B for about 3 seconds. The letter F will
disappear from the display.
Change activated carbon filters (carbon filter
saturation indicator - C).
After replacing the charcoal filter, depress
knob B for about 3 seconds. The letter C will
disappear from the display.
When the led in the lower right side is on, it indicates
that the cooker hood is ready for operation
(standby position), the flashing LED indicates
that the timer has been activated for selected
speed.
Warning!
The active carbon filter saturation function is not
activated.
In order to activate the carbon filter saturation indicator,
press buttons E and F simultaneously for 3 seconds.
Initially, only letter F will fbe displayed, then after the
3 seconds have passed, letter C will be displayed
as well, indicating that the carbon filter saturation
control system is active.
To switch off the system, re-press the same two
buttons: letter C appear on display and after 3
seconds letter it disappear and the device will be
switched off.
E - Knob to decrease the speed: from intensive speed
P to speed level 1.
F - Knob to increase (standby) speed to intensive speed
P.
Attention! Intensive speed P has a duration of 5
minutes after which the cooker hood automatically
sets the speed to level 2 (suction power).
If the hood fails to operate correctly, briefly disconnect it from
the mains power supply for almost 5 sec. by pulling out the
plug. Then plug it in again and try once more before
contacting the Technical Assistance Service.
ABCDEF
Operation 
Model with electronic controls
1- Motor OFF button
2- ON button and motor speed selection button 1 - 2 - 3 -
1 - 2 - . . . .
3- Speed 1 LED
4- Speed 2 LED and metal grease filter saturation LED (in
this latter case, the LED will flash - See instructions on
grease filter cleaning).
Once the grease filters have been cleaned, press button
1 for about 3 seconds until you hear the acoustic signal
(beep): the LED 4 will now stop flashing.
5- Speed 3 LED and active carbon filter saturation LED (in
this latter case, the LED will flash - See instructions on
active carbon filter replacement).
Once you have replaced the charcoal filter, press button
1 for about 3 seconds until you hear the acoustic signal
(beep). LED 5 will now stop flashing.
Warning!
The active carbon filter saturation LED is not activated.
In order to activate the active carbon filter saturation
indicator, press buttons 2 and 7 simultaneously for 3
seconds. Initially, only LED 4 will flash, then after the
3 seconds have passed, LED 5 will also start flashing,
indicating that the active carbon filter saturation control
system is active.
To switch off the system, re-press the same two
buttons: after 3 seconds LED 5 will stop flashing and
the device will be switched off.
6 - Intensive speed LED
7 - Intensive speed ON switch
This speed should be used when the concentration of
cooking fumes or odours is particularly strong (for
example when frying, cooking fish etc.). T h e
fast speed will run for about 5 minutes and then return
to the speed previously set automatically (1, 2 or 3),
or switch off if no speed was selected.
To turn off the fast speed, before the end of the 5 minutes,
press button 1 or button 2.
8 - OFF lamp button
9 - ON lamp button
If the hood fails to operate correctly, briefly disconnect it from
the mains power supply for almost 5 sec. by pulling out the
plug. Then plug it in again and try once more before
contacting the Technical Assistance Service.
1
2
34
56
7
89
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elica samurai at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elica samurai in the language / languages: English as an attachment in your email.

The manual is 1,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info